Magazines:  Real Estate Shopping: Adult Costumes  |  Kids Costumes  |  Cars  |  Guitars |  Electronics
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Alternative Cars, Part 4 Human Powered

Sounds impossible...

by Julian Edgar

Click on pics to view larger images


Last week in Alternative Cars Part 3 we looked at the possibilities of turbine-powered cars. This time we look at vehicles powered by humans.

A human-powered vehicle sounds like an oxymoron. How can just legs power a vehicle? However that reaction is more an indictment of the limited variety of available vehicles than any intrinsic impossibility. If the vehicle weighs – say – 30kg, can carry a person and their goods, can keep them dry and protected from the weather, and can achieve reasonable speed and range for urban use, then by most broad definitions it’s a vehicle.

For many people and in many environments, it’s also quite a viable option.

Function

Click for larger image

Human-powered vehicles that fit the above description already exist. They’re called velomobiles and are most popular in Europe.

The most frequently used configuration is a tricycle wheel arrangement, with two front steering wheels and a rear powered wheel. This format gives stability without the driveline requiring driveshafts with universal joints or a differential.

The rider lies back in a semi-recumbent seating position, so lowering the height of the vehicle and also providing greater comfort because of the large area of body support. The pedals are positioned forward of the rider and at, or a little above, the height of the seat base. The pedals, chain drive, gears and wheels all follow well-proven bicycle practice. For example, derailleur gears, internal hub gears, spoked wheels and so on are used.

Steering geometry of the front wheels is chosen to provide zero or negative scrub radius and Ackerman steering is usually implemented. Steering control is via fore-aft levers positioned either side of the seat or by a joy-stick-type of control between the rider’s legs. Suspension is often fitted.

Click for larger image

A key ingredient is a fully enveloping body work, either completely covering the rider or alternatively, allowing their head to remain exposed. These ultra lightweight bodies, that include an undertray, are shaped to give very low aerodynamic drag, vastly reducing the amount of required power needed at speeds over about 15 km/h. Compared with a conventional bicycle that on flat ground at 36 km/h requires a rider power of 345 watts to overcome wind resistance, a fully faired recumbent velomobile requires just 30 or 40 watts!

Some velomobiles are electrically-assisted and feature head- and tail-lights, windscreen wipers and indicators.

Advantages

Click for larger image

The advantages of a human-powered velomobile are many. If the cost of food is ignored, running costs are very low – effectively free in fact. The exercise has major health benefits and emissions are zero.

Human powered vehicles are quiet and in car terms, cheap. They take up little space on the road and because their maximum speed is relatively low, traffic density can be high. When used on dedicated cycle trails, commuting times can be quicker than conventional cars travelling on heavily congested roads.

If appropriately maintained, their life can be expected to be long, in turn reducing the cost per kilometre even further.

A human-powered vehicle with well designed suspension and steering can be both comfortable and fun.

Disadvantages

However, disadvantages are also many!

For people of average fitness, range and speed are severely limited. In hot environments the rider will need to shower and change their clothes after finishing their ride, which limits work commuting to relatively short distances to workplaces that provide appropriate shower facilities. In very cold environments the lack of heating is problematic.

Human powered vehicles are limited in carrying capacity, normally to just one person and minimal luggage. While the work effort of propelling the vehicle can be quite low, entering and exiting these vehicles requires agility and flexibility.

Use of human-powered vehicles (which are wider than bicycles) can be dangerous on roads that don’t provide appropriate lane space. Hills – even small hills – greatly increase the required pedalling effort.

In part because of their very small production numbers, velomobiles are about 5-10 times as expensive as a good bicycle.

Solution

The technology of human powered vehicles is well known. In terms of steering, suspension, power transmission, aerodynamics and seating, there is excellent existing knowledge. However, for human powered vehicles to take off, the following needs to occur:

  • Development and production of a velomobile by a major company. Current velomobiles (and human powered vehicles in general) are produced by boutique manufacturers - often small family companies - with very limited capital. Because the market is currently tiny, major bicycle manufacturers have not entered it. (And it can be argued that bicycle manufacturers are not particularly well placed to develop, manufacture and market velomobiles anyway.) The major development cost is in the body, which because of its extreme lightweight requirement, is best moulded from composites like carbon fibre.

  • Implementation of dedicated cycle paths that separate motorised vehicles and human powered vehicles on all but local feeder roads. Cycle path construction is certainly booming, but here in Australia at least, they often end abruptly (forcing riders onto main roads), are poorly maintained and are often placed where it’s easy to put them rather than satisfying traffic requirements.

Conclusion

Velomobiles clearly don’t suit all uses to which we put current cars - in fact, they couldn’t replace the majority of car trips. However, where the topography is flat, cycle ways are provided and single person trips are frequently short, human powered vehicles have the potential to become widely used.

Next week: steam powered vehicles

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
How racing rules should be re-written to help again develop relevant technology

Special Features - 24 November, 2009

Making Racing Cars Relevant Again...

Looking at the worth of bio-fuels

Special Features - 17 April, 2008

Biofuels: Friend or Foe

Stormwater and council inspection

DIY Tech Features - 20 March, 2012

A New Home Workshop, Part 6

How variable compression engine technology works

Columns - 4 April, 2008

Changing the Squeeze

Engines that don't need cams, rocker gear or cam belts!

Technical Features - 17 April, 2001

Camless engines

Do-it-yourself aero testing of an Impreza WRX

Technical Features - 23 June, 2007

Aero Testing, Part 2

The $10 lathe or drill press tachometer

DIY Tech Features - 11 August, 2009

A Drill Press or Lathe Tacho

Putting a super-bright LED interior light in your car

DIY Tech Features - 21 July, 2008

Upgrading to LED Interior Lighting

DIY flow testing of the intake

Technical Features - 31 July, 2008

Free-Flowing a Miata MX5

Wiring a home workshop for power

DIY Tech Features - 23 September, 2008

Building a Home Workshop, Part 7

Copyright © 1996-2017 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip