Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

Jaguar's Slippery Racing Cars

Tracking drag and lift changes on the aero Jaguar race cars of the 1950s

by Julian Edgar

Click on pics to view larger images

This article was first published in 2010.
Click for larger image

It’s now a long time since downforce aids were invented for racing cars. The use of inverted wings – and later, ground-effects tunnels – revolutionised the ability of racing cars to stick to the road around corners... especially high-speed corners. But developing downforce inevitably results in increased aerodynamic drag – the reason that the drag coefficient (Cd) figures of racing cars are nearly always so bad.

And, in turn, that makes nearly all racing cars poor examples to use when trying to reduce drag on road cars – or even to picture how drag can be reduced. The exceptions – racing cars with very low drag figures – are solar racers, and some vehicles in very limited categories with tiny engines. However, for other reasons, these cars also don’t make great role models for normal road cars.

In fact, to return to racing cars with low drag figures means taking a look back at the Fifties (and, to a lesser degree, the Sixties). And that’s what we’re going to look at here – not examining all the possible cars, but looking at just a handful of cars for which I have found aero data.

The Jaguars

One fascinating family of race cars for which data is available are the Jaguar racing cars of 1950 – 1955.

Click for larger image

In 1950 Jaguar raced the XK120, a car with 161hp and a frontal area of 13.86 square feet. At 100 mph, this car used 68hp just to overcome drag! Furthermore, while at rest the weight distribution was 48.5 per cent front and 51.5 per cent rear, at “speed” (this number is not defined but you can assume - say – 100+ mph) this weight distribution changed to 46:54.

Click for larger image

In other words, the front of the car developed lift. (You could also argue that these figures show the rear developed downforce, or some combination of front lift and rear downforce, but the reality of such shapes is that downforce simply does not happen.)

With the drag power (68hp), the frontal area (13.86 square feet), and the speed (100mph), you can calculate the drag co-efficient (Cd) of the racing XK120. See Power to move if you want more on how to do this.

Click for larger image

By 1951, Jaguar engineers, working very hard on reducing drag, had made some major improvements. The car was the C-type and frontal area dropped only fractionally to 13.8 square feet. But drag power dropped by a massive 24 per cent to 53hp! But there was a problem looming: static weight distribution was 51.5: 48.5 but when travelling at speed, this altered rather dramatically to 58:42! A light tail, anyone?

Click for larger image

By 1952 we had the Series II C-type. This kept the same frontal area (13.8 square feet) but the extended tail (that would have kept airflow attached longer, thus reducing the size of the wake) reduced drag power by another 21 per cent to 42hp.

Click for larger image

So from 1950 to 1952, drag power had been reduced by a massive 38 per cent! But the trade-off was equally massive: static weight distribution was 51.5:48.5 but at speed this altered alarmingly to 65.5:34.5! That rear kept the flow attached but boy, did it create lift!

Click for larger image

It was time for a rethink, which came with the 1953 prototype D-type. Frontal area was up a tad at 13.9 square feet and drag power was down only a little to 40hp. But what about the high speed weight distribution? Static weight distribution was 54:46 but the fast-moving weight distribution was much improved at 50.5:49.5.

Click for larger image

The Jaguar aero engineers must have been wondering where they could go from here, but with the 1954 D-type they managed to drop frontal area by 10 per cent to 12.5 square feet, neatly explaining the decrease in drag power by the same percentage to 38hp.

Click for larger image

Weight distribution – both static and aero-active - also changed only a little, to 53.5:46.5 at rest and 51:49 at speed.

Click for larger image

1955 saw a small increase in frontal area (to 12.8 square feet) but, amazingly, a further drop in drag power to just 32hp! So to again to compare with 1950, in five short years the drag power had been reduced by more than 50 per cent, from 68 to 32hp! (And, to put the total car performance in context, at the same time engine power had risen from 161hp to 270hp!)

Other Cars

Click for larger image

The 1966 Porsche Carrera Long tail had only 220hp available and yet could reach a top speed of 171 mph (265 km/h); its quoted Cd was 0.33.

Click for larger image

The almost unknown CD Peugeot 66, also of 1966, could reach 152 mph (245 km/h) on just 105hp!


Perhaps self-evidently you don’t look at these pics and diagrams and then race out to the shed, electric jigsaw in hand and an avid desire to modify your car’s shape. But any material of this nature is grist to the mill: I for one was amazed at the variation in the lift figures (or, if you wish, the change in front:rear effective weight distribution) with alterations in shapes of the Jaguars...


The Jaguar photos (but not the diagrams) have been drawn from a number of sources and so may not accurately reflect the racing configurations used in the cited years.


Berry, R, Jaguar – Motor Racing and the Manufacturer, Aztex Corporation, 1978 ["an exact transcript of the illustrated paper as read before the Society of Automotive Engineers, San Francisco chapter, August 25, 1976"]

Hucho, W.H. (Ed), Aerodynamics of Road Vehicles, Butterworths, 1987

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
Part two of an R32 Skyline GT-R modification process

DIY Tech Features - 6 September, 2011

GT-R Unleashed

Lunar Rover: the only car literally out of this world

Special Features - 14 October, 2008

World's Greatest Cars, Part 2

The story behind the Datsun 240Z

Special Features - 16 July, 2008

The First Zed

Avoiding damaging bangs

Technical Features - 21 August, 2012

Detonation and Pre-Ignition

Getting a home workshop to the lock-up stage

DIY Tech Features - 2 September, 2008

Building a Home Workshop, Part 4

Achievable and real-world ways to reduce your fuel bill

Special Features - 25 August, 2008

Improving Fuel Economy

Building an adjustable temperature alarm - and more!

DIY Tech Features - 27 October, 2009

eLabtronics EZ System, Part 4

Want to see where you're going with modifications? Measure the airflow meter output.

DIY Tech Features - 20 January, 2005

Using the Airflow Meter as a Dyno

Then the world's most powerful six cylinder passenger car diesel

Technical Features - 6 June, 2005

BMW's Twin Turbo Diesel

Got an old cordless drill around the place? Here are the parts you can salvage from it!

DIY Tech Features - 8 May, 2008

A Heap of Parts for Nothing!

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip