Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Modifying Electronic Car Handling Systems, Part 4

The step by step of switching off traction control while leaving the stability control working!

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Turns off traction control without changing stability control
  • Uses relays to do the switching
  • ABS operates normally
  • Step-by-step of relay board construction
  • Part 4 of a 4-part series
Email a friend     Print article
This article was first published in 2004.

Over the last few weeks in this series we’ve shown you the differences between stability and traction control systems, and how you can turn off one (traction control) without turning off the other (stability control). We’ve also covered the use of three relays to allow you to have switchable on/ff traction control while still retaining ABS and stability control functions. (If you’re just joining us now, start at Part 1 – Modifying Electronic Car Handling Systems, Part 1 - otherwise it’s likely you’ll soon be completely lost.)

This week, in the last of the series, we’ll show step-by-step how to build the relay board and connect it up. The cost is low and while the wiring is a little fiddly, it’s just a case of taking it slowly and carefully.

The Parts

Click for larger image

As covered last week, the switchover system uses three relays. The Changeover Relays need to be Double Pole Double Throw (DPDT) 12V designs, while the Switching Relay can be a Single Pole Single Throw (SPST) 12V design. At the risk of confusing you, you can also make the Switching Relay a DPDT design (and then use only half of the contacts) – using all-DPDT designs makes it easier to source the relays. You just buy three that are the same.

In addition to the three relays, you’ll also need some pre-punched circuit board, terminal strips and a box. At the end of this story we’ve listed the parts from Australia’s Jaycar Electronics – if you live outside of Australia you can order them by mail order, or alternatively source much the same parts at any electronics supply shop. None of the parts is anything unique or hard to get.

Wiring the Relays

The key part of the system is making sure that the right relay contacts connect to the right parts of the car. Easiest is to wire the relays on a small pre-punched piece of board, mounting both the terminals and the relay on the board. That way, you need only connect from the screw terminals to the car, rather than trying to connect directly to the relay terminals themselves.

Click for larger image

The pin-outs of DPDT relays varies, depending on brand. Shown here is the approach taken with the Jaycar SY-4059 relays, which have a pin-out (viewed from underneath!) that looks like this.

Click for larger image

The connections that need to be made from the terminals to the relay pins are shown here. The way in which you connect the pins to the terminal strips is up to you, but we chose to use short lengths of insulated wire. That way, it’s easy to arrange the wires without concern for short-circuits. That’s the upside; the downside is that the end result looks is harder to follow in pics.

Click for larger image

The first step is to connect the relay contacts to the terminal blocks.

Click for larger image

The next step is to wire the coils of the two Changeover Relays through the Common and Normally Closed contacts of the Switching Relay (black and red wires). The brakelight input can also be added (white wire).

Click for larger image

The connection for the traction control off warning light can then be made. Note that this warning light isn’t obligatory but it makes sense that the driver is alerted when the traction control system is off – none of the car’s OE warning lights will show this.

Click for larger image

Wired into place the relays and terminal strips should look like this. Note that to make the soldering easier we glued the relays and terminal strips to the board (using instant glue) before starting the underneath wiring.

Click for larger image

Now that you’ve built the relay board it’s time to turn it over. This is what the connections look like from above.

 

Traction Control

Pin Number

Relay Function

Left

Left Rear ECU input positive

1

Common

Left Rear ECU input positive

2

Common

Left Rear Speed Sensor

3

Normally Closed

Left Rear Speed Sensor

4

Normally Closed

Left Front ECU Input positive

5

Normally Open

Left Front ECU Input negative

6

Normally Open

Right

Right Rear ECU input positive

7

Common

Right Rear ECU input positive

8

Common

Right Rear Speed Sensor

9

Normally Closed

Right Rear Speed Sensor

10

Normally Closed

Right Front ECU Input positive

11

Normally Open

Left Front ECU Input negative

12

Normally Open

Click for larger image

Here’s the system installed but before the wiring was tidied and the lid placed on the box. Note the use of sticky labels on the wires – important if you’re not to get lost in the wiring.

Conclusion

If you have a car with stability control and would like a bit more throttle control over the way the car drives, this approach may be for you. It allows you to easily switch the traction control on or off without affecting the stability control or ABS and is a cheap and relatively straightforward modification.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Step by step of keeping drill bits sharp

DIY Tech Features - 20 August, 2008

Sharpening Drill Bits

Why turbo engines give better fuel economy

Technical Features - 13 February, 2008

Turbo'd For Fuel Economy

A brilliant way of developing and testing space-frame structures

DIY Tech Features - 17 February, 2009

Zero Cost Modelling of Space-Frames

The revs and loads at which engines use least fuel

Technical Features - 10 April, 2008

Brake Specific Fuel Consumption

Testing vortex generators on slippery cars

Special Features - 18 October, 2006

Blowing the Vortex, Part 4

A breakthrough car that proved to be a step too far

Special Features - 6 August, 2008

The NSU Ro 80

A revolutionary fuel saving device that works

Columns - 25 August, 2009

FuelSmart, Part 2

Wiring a home workshop for power

DIY Tech Features - 23 September, 2008

Building a Home Workshop, Part 7

Techniques to revolutionise your car modification

DIY Tech Features - 31 March, 2009

Ultimate DIY Automotive Modification Tool-Kit, Part 1

How to make your own airbox - and test its effectiveness

Technical Features - 19 April, 2008

Building and Testing an Airbox

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip