Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Setting Up an In-Car PC, Part 3

Organising the LCD display

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Selecting an LCD
  • Mounting the screen
  • Connecting the screen to the PC
  • Reducing audio noise from the LCD power supply
Email a friend     Print article

So far in this series we’ve covered an overview of setting up an in-car PC (Setting Up an In-Car PC, Part 1) and getting the audio from the PC to your normal car sound system (Setting Up an In-Car PC, Part 2). This week we’re going to concentrate on the visuals – selecting, wiring-in and mounting an LCD screen in the cabin. As the main interface with the PC, the LCD is important – you want it to be bright, sharp and look good.

Selecting

To give the greatest universality of PC selection, it’s best to use a screen that takes a direct VGA input. That is, the screen can be plugged into any PC video card and will fire up straight away without anything further needing to be done.

Click for larger image

The LCD that we bought also has another important function – a USB touch screen. This allows the PC to be controlled by touching the icons on the screen, removing the need for a mouse or other pointing device. In this first in-car PC iteration we’re not using this function but having a screen with this capability opens up a lot of functionality, so you keep this feature in mind when selecting the display.

The screen that we bought was the 7-inch Lilliput XGA TFT touchscreen. The design uses a Sharp screen, has two RCA video inputs (in addition to its VGA input), has built-in speakers and comes with a remote control. It was purchased through eBay from Extreme Audio Electronics of Hong Kong. The transaction was sweet – payment through Western Union Auction payments and very fast freight. Including freight, the total cost was AUD$408 – no GST or import duties were charged.

Mounting

The location of the LCD is important.

  1. You probably want it visually accessible to as many people in the cabin as possible. This includes the driver and front seat passenger as well as potentially the rear passengers. However, the driver must also be able to look at it without diverting his/her eyes too far from the road.
  2. You don’t want the background to the display to be bright – for example, a front roof-mounted display sounds like it would fulfil most of the previous criteria but on a sunny day, the screen will be hard to read because of the bright background.
  3. The LCD must be located so that it doesn’t reflect the light coming in through the windows, especially the rear glass.
  4. The LCD should be shaded as much as possible from direct light.

The reality is that you should hold the screen in lots of different locations around the cabin before making up your mind.

In this car – a Toyota Prius – one of the options was to place the screen directly behind the steering wheel. Like some other Toyotas, the Prius has its instruments located in the centre of the dash, just below windscreen level. This leaves the space behind the steering wheel free for the LCD screen – and the driver can then see it beautifully. However, this location prevents anyone else in the car being able to see the screen...

Click for larger image

So the final spot that was chosen was in the middle of the dash, mounted below the heater/ventilation controls and with the screen angled upwards. The initial angle that was tried proved to reflect light from the rear window straight towards front seat viewers, so the screen was angled a little more so that it was reflecting light from the centre of the underside of the roof. (In cars with sunroofs, you should always try different locations with the sunroof fully open!)

The Lilliput screen comes with an adjustable angle mount equipped with a large pad of double-sided sticky foam. But in this application (and in pretty well all car uses that we can think of) there won’t be any big, flat surfaces that this foam can get a good grip on. Initially, the sticky foam pad was unscrewed from the adjustable-angle part of the mount and a new support made. However, the plastic adjusting screws on the provided bracket proved to be not up to the task and so in the end a completely new mount was made from aluminium.

This mount is screwed to a small existing shelf, with the screws hidden inside the dash. This mount causes the top of the screen to push back against the dash – it’s cushioned with a small piece of foam rubber. In this way, screen vibration is kept to a minimum.

LCD Power Supply

Click for larger image

The LCD comes with its own power supply. This is terminated in a cigarette light plug which needs to be cut off to allow the cord to be hard-wired into place. Make sure that you work out the polarity of the cord (the tip of the cig lighter plug is positive) before cutting the plug off. The connections should be made to an ignition-switched 12V supply and earth.

However, as briefly covered last week, we found that if the LCD power supply was placed close to the FM modulator or line-level signal leads, it caused a lot of noise in the audio system. Furthermore, the power supply (an electrically noisy switch-mode design) proved to be also injecting noise back into the car wiring... noise that was then picked up by the FM modulator. This was easily demonstrated by switching off the LCD – some of the background noise in the audio then went away.

The technical advice of Silicon Chip magazine’s John Clarke was sought and it was his suggestion that rather than noise suppression techniques be applied to the existing power supply, a whole LCD new power supply be built. This step isn’t as daunting as it sounds – it takes about 15 minutes and less than AUD$10 to build a new power supply.

While the LCD is happy working on 11-13V, the problem in a car use is that there can be all sorts of nasty voltage spikes surging around in car wiring. (That’s presumably why Lilliput provide the extra power supply.) So the primary requirement of a new power supply isn’t to precisely regulate voltage but to make sure that an over-voltage situation cannot occur.

To build the simple power supply you’ll need:

  • 1x 16V zener diode – Jaycar cat no ZR-1416
  • 1x 5W 1 ohm resistor – cat no RR-3220
  • 1x 10uF 25V electrolytic capacitor – cat no RE-6070
  • 1x 100uF 25V electrolytic capacitor – cat no RE-6140
  • 1x 12V 7812 voltage regulator – cat no ZV-1512
  • Small amount of punched board – cat no HP-9562
  • UB5 box – cat no HB-6015

You’ll also need a small heatsink or piece of scrap aluminium.

Click for larger image

This is the circuit. The resistors prevents large current flows, the zener diode acts as a safety valve bypassing any voltages that exceed 16V, and the voltage regulator drops the voltage to a max of 12V. (The capacitors stabilise the action of the regulator.)

Click for larger image

The circuit can be physically laid out on the punched board exactly as shown here, making it easy to construct. Note that the voltage regulator, capacitors and zener diode are all polarised – have a close look at this pic of the built power supply (click on the image to enlarge) before starting construction.

Click for larger image

Here’s the underneath view of the completed power supply. Easy, huh?

Click for larger image

Both the resistor and the voltage regulator will get warm – that’s why a heatsink is needed on the voltage reg. The one here was salvaged from old consumer equipment and then cut down to suit. Once constructed and mounted in a box, the power supply can be tucked from sight under the dash.

The LCD Cable

Unless you find a spot to mount the PC that’s within the cabin of the car, it’s a certainty that you’ll need to run an extension cable for the screen. VGA extensions are commonly available in 1.8-metre lengths but you’ll usually need something more like 4-5 metres long. This is stretching the capability of the cable – so you’ll need to pick a high quality design with good shielding and ferrite rings at each end. We used the 5-metre Jaycar WC-7588 XVGA Monitor Extension Cable, which cost AUD$19.95. A female/female adaptor was also needed (cat no PA-0876 at AUD$5.80).

Unfortunately - for reasons that we’re not sure of – when we got it home, the 5 metre cable proved to actually be 10 metres long! This length introduced some noise into the signal – when using this ultra-long cable, the LCD display showed a slight double image. Since only about 4 metres was needed, the long cable was cut and shortened. This is a fairly tricky operation requiring rejoining internal braids as well as the 15 wires – see the breakout box ‘Joining Cables’ for more.

It’s almost certain the screen image won’t be as good with the extension cable in place as without it. That’s just the way it is – but the effects can be minimised if you pick the default screen displays and colours carefully – more on this later.

Click for larger image

When doing the cable runs, make sure that there’s sufficient room under the trim to hide the connectors. As with the audio cables, tape the connectors up to prevent inadvertent grounding and make them more secure.

The Results

Click for larger image

So how well does the screen work on the road? The main problem is that it cannot be easily seen if it’s in direct sunlight. Positioned low on the dash, the LCD is mostly shielded from direct light, but at times it can still be flared out. A solution might be to place a short shield around the sides and upper surface – even a shield only 10mm long would remove the problem most of the time. Other than this issue, the screen works very well.

Next week: A custom suspension mount for the PC, and finishing off the system.

Joining Cables

Cables for both audio and video often are of an electrically shielded design. This places a braid or aluminium foil around a central conductor that’s insulated from the shield. As the name suggests, a shielded cable protects the signal from interference.

If you are shortening a shielded cable, it’s important that you maintain the shield. The easiest way of doing this is to join the conductors conventionally (eg bind them together and then solder the connections), insulate the centre conductor join with tape, and then wrap aluminium foil around the braid across the width of the join. That way, the shield is continued.

If the cable that you are working has multiple shielded internals, you need to do each one individually.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Using a multimeter

DIY Tech Features - 6 January, 2009

How to Electronically Modify Your Car, Part 4

Measuring analog and digital signals

DIY Tech Features - 24 February, 2009

How to Electronically Modify Your Car, Part 11

Tweaking the engine management to run non-standard mixtures in closed loop

DIY Tech Features - 12 January, 2005

Altering Closed Loop Mixtures

Stormwater and council inspection

DIY Tech Features - 20 March, 2012

A New Home Workshop, Part 6

Easy, cheap and effective

DIY Tech Features - 30 April, 2013

Building a home sound amplifier, Part 1

Turbine cars promised so much - but they're not the answer

Technical Features - 27 September, 2007

Alternative Cars, Part 3 - Turbine

So what stuff is worth salvaging out of old air conditioners?

DIY Tech Features - 20 April, 2010

The Good Bits out of old Air-Conditioners

Inside the construction of some aluminium cars

Technical Features - 2 September, 2008

Aluminium Cars

Buying and using a lathe

DIY Tech Features - 29 November, 2007

Making Things, Part 8

Under $10 for a remote-controlled immobiliser!

DIY Tech Features - 27 November, 2012

DIY classic car immobiliser

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip