Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


The NSU Ro 80

A step too far

by Julian Edgar

Click on pics to view larger images


This article was first published in 2008.
Click for larger image

When the NSU RO 80 was released in 1967, the car was greeted with universal acclaim.

It immediately won Car of the Year awards, and road tests in Europe, the US and Australia were glowing in their praise. Here was a car with not only a brand new design of rotary engine, but also a stylish and elegant body that had an aerodynamic drag figure superior to nearly everything. Add to that front-wheel drive, four wheel disc brakes, class-leading power steering and a well-developed suspension. And all from a company, NSU, previously known only for motorcycles and small rear-engine cars!

The Ro 80 was a tour de force – but it sent NSU broke.

So how did one of the most advanced and welcomed cars ever made prove such a disaster? It’s a fascinating technical story.

Let’s start with the engine.

Twin Rotor Wankel

Click for larger image

Mounted longitudinally at the very front of the car, the twin rotor Wankel used peripheral intake and exhaust ports and displaced 1 litre (497.5cc x 2). While one of the very first production cars in the world to use a rotary engine, the Wankel was certainly not an unknown design to NSU: at the time of release of the Ro 80, the company had built 3000 small rotary outboards and 2500 single rotor NSU Spider cars.

The Ro 80 engine used aluminium alloy rotor housings and a 9:1 compression ratio. The rotor tip seals were cast iron and the wearing surface of the rotor housings was a nickel and silicon carbide coating that was electrically deposited. Two spark plugs per chamber were fitted (in later engines this was reduced to one plug per chamber) and the two plugs were fired simultaneously. Ignition on early engines was by traditional coil; this was upgraded to electronic ignition on later cars.

Carburetion was by a twin-choke Solex, the unusual aspect being the use of one very small choke (18mm) and very large choke (32mm). These chokes fed long intake runners that merged only at the inlet ports. The exhausts of each rotor were kept completely separate.

Click for larger image

Power was listed at 113hp at 5500 rpm and peak torque 117 ft-lb at a high 4500 rpm. The peripheral porting helped give a strong top-end but low-rpm torque was poor – this graph is an interesting comparison of the Ro 80’s power and torque outputs compared with the contemporary Rover 2000TC, itself not a scintillating engine. As can be seen, the 2 litre Rover has about a third more torque at lower revs.

The Wankel was said to weigh only two-thirds that of a reciprocating engine developing the same peak power, and furthermore, NSU said the cost of producing the engine would be reduced to well below that of a conventional engine – the target was 60 per cent of the cost of a six cylinder of equivalent power.

At the time of first release, NSU engineers were said to have overcome the development problems of the rotary: chatter marks on the epitrochoidal surface, apex seal wear and high oil consumption. The car’s warranty was two years or 24,000 miles – far better than the then prevailing average.

Road testers and owners universally commented on the engine’s smoothness and ability to rev. Later, they also commented on the incredibly short time the engines lived...

Transmisison

Click for larger image

Bolted to the back of the rotary was an interesting transmission. Similar to the Sportmatic design used in some Porsches of the time, the Fichtel and Sachs semi-automatic used a vacuum servo-controlled clutch, a torque converter and a 3-speed all-synchro transmission. Incorporated in the gear lever knob was a micro-switch that triggered the clutch.

In normal town use the gearbox could be left in second gear, being driven as a full automatic. However, for better performance, the gearbox was changed conventionally.

This semi-auto trans was the only transmission available; it was fitted after NSU engineers experienced snatching in the driveline on throttle lifts. (Remember that peripheral porting of the rotary!) The presence of the torque converter overcame this problem.

Click for larger image

Some drivers loved the transmission, while others hated it. It appears that the system had to be finely adjusted if jerkiness – especially on down-changes – and noise were to be avoided. In any case, off-the-line acceleration was always leisurely.

Drive was to the front wheels - the whole engine and transmission being mounted ahead of the axle line.

Just the refined and sophisticated driveline would have made the Ro 80 a startlingly innovative car, but there was far more.

Suspension

Click for larger image

The front suspension was not groundbreaking in the mould of the contemporary Citroen hydro-pneumatic systems, and the hydraulic Hydrolastic system fitted to some Austin models, but it was still extraordinarily well developed.

Front suspension used MacPherson struts, something then still relatively rare on a front-wheel drive car. The front coils were offset from the axis of the strut to reduce stiction and side-loadings, and the front wheels had no less than 7.4 inches of travel. An anti-roll bar was used – another then unusual aspect of the design was that the anti-roll bar did not help located the wheels; instead a lower triangulated wishbone was used. (Like many aspects of the Ro 80, this is something we now take for granted in most MacPherson strut designs.)

Click for larger image

Rear suspension took more than a passing glance at BMW and Mercedes Benz practice and used semi-trailing arms (angled at only 10 degrees) and mounted on a sub-frame. Like the front suspension, spring and dampers were concentric. No rear anti-roll bar was fitted, something that certainly raises modern eyebrows. Rear wheel travel was an astonishing 10 inches.

Road testers and owners alike commented on the extraordinarily comfortable ride, one that had little pitch. Initial tests were also glowing in their praise of the car’s handling, it being said to have only a touch of understeer. However, later tests – perhaps within the context of improving front-wheel drives – talked about a lot of body roll and understeer that could not be throttle-controlled. The tail, for example, stayed resolutely planted, no matter what was done with the accelerator pedal or steering!

Tyres were to modern eyes tiny – just 175 width on 14 inch rims (alloy on later cars). The specified tyres were, however, very high performance – Michelin XAS radials.

Steering

Click for larger image

The ZF steering used a geared rack and pinion system, aided as standard by a hydraulic ram. Steering feel was said to be excellent at all speeds, however, as time passed and power steering became more common, the 3.75 turns lock to lock attracted some criticism.

Very unusually for the time, the steering column did not extend past the front bulkhead, improving safety in the event of a front-end crash. In contrast, most cars then had steering columns that extended well forward; the steering wheel being pushed into the driver as the front crumpled.

Steering Geometry?

Click for larger image

One of the most interesting aspects of the steering is one that is not actually identified in accounts of the car – the amount of scrub radius provided by the front steering geometry.

By all accounts, the Ro 80 was wonderfully stable in poor conditions, something often associated in the contemporary road tests with the front-wheel drive chassis. However, looking at the drawings of the Ro 80, it appears that very little scrub radius was used – and in fact, depending on where the exact pivot axis is drawn, it could even be negative rather than the then-universal positive.

Negative scrub radius steering has the ability to self-correct when one wheel encounters more resistance than another, and since the descriptions in the road tests again and again describe the uncanny ability of the car to stay straight, we wonder if the Ro 80 wasn’t in fact the first car to use this steering geometry...

At minimum, it certainly had very little positive scrub radius.

Brakes

Click for larger image

Even in the braking system the Ro 80 was unusual for the time.

Front discs were large and mounted inboard either side of the gearbox. Rear brakes were also disc and incorporated separate drums for the handbrake. The braking system used a tandem master cylinder with two independent circuits – one circuit operating all four wheels and the other, just the front wheels through the second pair of cylinders on the twin pot brakes. The rear brakes used a load-sensitive proportioning valve.

Body

Click for larger image

The body shape of the Ro 80 was quite startling. A low nose, high boot, concealed rain gutters and lack of ornamental chrome gave rise to plenty of comments that the body was shaped by engineers, not stylists! (The Ro 80 doesn’t look startling today because most of the styling cues were picked up in the later Audi 100, a car that set the aerodynamic sedan styling agenda for the next 20 years.)

Click for larger image

The claimed drag coefficient was 0.355, a figure then at least 25 per cent better than achieved by a typical car of the same class. Wind tunnel wool tuft testing shows amazingly good flow, especially in the reattachment on the boot-lid. (This author has never seen any evidence than any other three-box cars of the era achieved attached flow on the final third of the car. Typically, any wool tuft pics are careful not to show this area!)

The low drag co-efficient (and relatively small frontal area – the car was quite low) were responsible for the ability of the Ro 80 to run to 117 mph on only 113hp (that’s 188 km/h on only 84kW!).

Interestingly, a US magazine measured aerodynamic lift at 100 mph (160 km/h) at a massive 150 lbs (68kg) front and 140 lbs (64kg) rear. At least the lift was largely the same front and rear...

The car had a mass of about 1300kg.

On the Road

Click for larger image

The Ro 80 had a range of competitors; in most European markets it was compared with cars like the Rover 3.5, Jaguar XJ6 and Mercedes 280SE. Interestingly, in acceleration to 100 km/h, maximum speed, fuel economy and the standing quarter mile, it was largely inferior to these cars. In fact, only in fuel economy did it comprehensively beat the thirsty XJ6.

Another car that the Ro 80 was compared to was the Citroen ID20. Against the Citroen it had similar performance but had much poorer fuel economy. However, the NSU handled better.

A 1968 road test best summaries the strengths and weaknesses: Wankel engine smooth and quiet; performance good, economy poor; very quiet at speed and handling outstanding; well made, roomy and very comfortable.

What Went Wrong?

Click for larger image

Initially the demand for the Ro 80 was so high that there was a waiting list. Owners raved about the cars, particularly their ability to travel long distance in silent stability. Fuel economy, especially away from city confines, was within the ballpark of other cars of the same performance and if that performance was a bit sluggish off the line, well the mooted triple rotor Ro 80 would soon fix that.

And then, all at once, the whole thing came crashing down.

Simply, the innovative rotary engine proved to have a fearsomely short life. Engines worked perfectly for, in some cases, just days. Few cars did more than 50,000 kilometres on the original engine. The standing joke was that if you were driving a Ro 80 and saw another, you’d not wave but instead hold up the number of fingers that corresponded to how many engines you’d gone through...

Click for larger image

The eccentric shaft was upgraded with massively increased lubrication, tip seals were modified, an over-rev dashboard buzzer added, the ignition system and number of spark plugs changed – but still engines failed. And not only did they fail catastrophically, but owners also complained about oil-fouled plugs and difficult starting. One enthusiast driver recounted that he became adept at changing plugs, removing carburettor jets and blowing through them, resetting the clutch servo and adjusting idle speed! And even then, that car’s engine died at just over 30,000km...

At least maintenance oil costs were reduced – the engines used so much oil that the factory decided to drop oil changes, instead using a ‘total loss’ approach. To be fair, oil was always intended to be injected into the combustion chambers, but the mind boggles at the thought of an oil consumption so high the complete sump contents were changed frequently enough to never need draining...

When engines failed NSU replaced them at a nominal charge (and often free), but the costs of doing so sent the company into a downwards spiral that was arrested only when it was taken over by Audi/Volkswagen.

Conclusion

The Ro 80 remains one of the few really brave cars launched by any car company in the world. (Arguably, it took until 1998 for Toyota to match the scale of innovation with the Prius.)

Designed from the ground-up for the new-age rotary engine, the Ro 80 incorporated the very best clean-sheet design aspects that could be then integrated into a safe and stylish car. Compared with its German prestige competitors, it was daring; perhaps only the French Citroen went even further. Perhaps not inconsequentially, Citroen was also working on a rotary powered car – it also proved a failure.

However, the NSU engineers’ work was not in vain: many innovations of the Ro 80 were to become mainstream over the next two decades – but the rotary engine was not one of them.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Changing the weight of electronically-controlled power steering

DIY Tech Features - 26 February, 2002

Modifying Speed-Sensitive Power Steering

Turning the voltage switch into a standalone temperature or light switch

DIY Tech Features - 29 July, 2008

The eLabtronics Voltage Switch, Part 2

How they built the fastest diesel on Earth

Special Features - 30 January, 2007

350.092 mph - Breaking the Diesel Speed Record

Developing a new Human Powered Vehicle suspension system

DIY Tech Features - 13 July, 2010

Chalky, Part 8

There are good technical reasons why steam could return

Technical Features - 9 October, 2007

Alternative Cars, Part 5 - Steam

Useful parts for nothing

DIY Tech Features - 6 October, 2009

Getting the Good Parts from Scanners!

DIY timer module adds delays or extended 'on' periods to any electric car function

DIY Tech Features - 1 September, 2008

The eLabtronics Timer

An amazing torque curve...

Technical Features - 7 July, 2009

BMW's V12 Twin Turbo

A dozen bits to find at the truck wreckers.

Technical Features - 29 August, 2008

Junkyard Dawg

Volt, amps and ohms

DIY Tech Features - 16 December, 2008

How to Electronically Modify Your Car, Part 3

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip