Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Pure Pipe Perfection 2 - Introducing the Secret Weapon...

It's time for an exhaust system revolution... A variable back-pressure exhaust valve that makes your car quiet at light loads, and yet still lets it breathe when the hammer's down!

By Julian Edgar, research and pix by Michael Knowling

Click on pics to view larger images


Last issue we covered the building and fitting of a high performance exhaust to a Commodore VL Turbo. It was an exhaust system fairly conventional in nature - 3-inch after the first flange, high-flow cat, mandrel bends and a single straight-through muffler - although it has to be said that it was far cheaper than most exhausts of this type! And, as you'd expect with just the cat and single muffler, it was also louder than the standard exhaust. Not really loud mind you, though prob too loud for some people's tastes.

But as we then implied, we have a secret weapon at our disposal. It's one that can make this exhaust - and pretty well any other - quiet enough to pass legal tests, while still being able to flow an awesome amount of exhaust gas. And the weapon that let's us do this? It's a device that effectively makes the exhaust a variable flow design, so that for all intents and purposes the exhaust is small at times of low load - and a whopper when your foot is down hard!

VariFlow System

Click for larger image

Invented by Kevin Davis of the New South Wales town of Wollongong, the design was developed initially as a result of Kevin getting sick of being booked for excessive exhaust noise. Surely, he thought, there must be a better way of getting low noise than just fitting a smaller or more restrictive exhaust system? The result of those musings was the VariFlow concept. Some three years later the design has passed through a number of iterations, with most of the changes aimed at making the valve live under the combined stress of very high temperatures and corrosive exhaust gases.

Fundamental to the operation of the system is the relationship between exhaust noise and backpressure. As backpressure increases, noise is reduced. This helps to explain the use of the restrictive and quiet systems fitted by most OE manufacturers to their cars. At the other extreme, a huge exhaust will have very little backpressure and as a result will often be noisy. (Increased backpressure makes mufflers work more effectively, and also often seems to reduce resonances - the hollow booming that occurs in big pipes at certain engine revs and loads.)

The heart of Kevin's VariFlow system is a variable opening valve that's located within the exhaust. This assembly consists of a butterfly constructed from 316-grade stainless steel, mounted within a cast alloy housing. The valve is opened and closed by a large vacuum actuator. The aluminium housing containing the valve is bolted into the exhaust pipe, with this made simple by the provision of two 10-mm steel flanges. Each flange is welded to a section of exhaust pipe, with the aluminium housing then sandwiched in between, being securely held in place by through bolts. This arrangement allows the easy removal of the valve if that's required, and also overcomes the problem of trying to weld the alloy valve body to the mild or stainless steel exhaust pipe. The insertion of the valve into an already constructed exhaust is also straightforward.

Click for larger image

Engine vacuum is used to operate the valve's control diaphragm, with the vacuum being used to close the valve against an internal spring. When vacuum is removed, the butterfly is able to open a full 90 degrees - posing very little restriction to exhaust flow - while at the other extent of its rotation, it can nearly close. (As with the throttle butterfly on a car, an adjustable stop prevents the valve from ever closing fully, even under a strong vacuum feed.)

And if that was all there was to it, you'd still have a pretty good system!

The exhaust valve would be nearly closed at lowest engine loads (highest vacuum) and most widely open at highest loads (lowest vacuum). Straightaway you can see that this will give a quiet exhaust system on cruise, and a loud (but excellent flowing) system when you're accelerating hard. However, what about if you're free-revving the engine at idle - as happens when the authorities are testing your car for noise? In that case, as manifold vacuum decreases, the valve will start to open, heightening noise. To avoid this problem, and also to allow the system to work even more effectively in normal use and on turbo cars, Kevin Davis has developed a full control system.

Control Box

Click for larger image

Housed in a large (155 x 105 x 80mm) alloy box, the control system consists of a very sensitive user-adjustable pressure switch, two solenoid valves, and an electronic delay circuit. So how does it work?

If the sensed exhaust backpressure is greater than the switch-on point of the pressure switch, the switch electrically opens a bleed solenoid, which lets some of the vacuum escape from the line leading to the actuator diaphragm. At the same time, another solenoid is switched to dump the exhaust backpressure signal. The result of this is that the exhaust valve starts to open. As the valve opens, backpressure falls, so opening the backpressure switch. This cuts off power to the vacuum and exhaust gas pressure bleed solenoids, re-establishing the backpressure signal and vacuum feed to the actuator. The valve then starts to close. Consequently, backpressure again starts to rise, starting the whole cycle all over again. In fact, the cycle can happen at up to eight times a second, resulting in the backpressure being maintained within a narrow window. Setting the sensitivity of the pressure switch determines how much backpressure is held in the exhaust.

Note that this elegantly simple system means that the valve responds in its actual opening angle to exhaust flow, always holding the same exhaust backpressure. This means that if you set the system to provide (say) 2 psi of backpressure at moderate loads, the valve will automatically open just far enough that a 2 psi backpressure is also maintained at one-quarter load, one-half load - or three-quarters load. (Obviously the pipe diameters and mufflers will need to be able to provide 2 psi or less backpressure if this example is to be realised in real life!). That's radically different to the characteristics of a normal exhaust, where backpressure at low loads is usually zero, rising as load increases.

Click for larger image

However, there will be some situations where the dialled-in backpressure will still result in a power deficit, especially if you set the backpressure relatively high to keep the car quiet in normal driving. To overcome this, a micro-switch is mounted on the throttle and the facility for a dashboard over-ride switch is also provided. At full throttle the microswitch trips the solenoids, resulting in the butterfly rapidly moving to its fully open position. Flicking the dash switch does the same - it's the one to touch if you just want max performance and damn the noise! In order that the valve stays open during gearshifts made between doses of full throttle, the electronic delay circuit maintains the valve in its fully-open position for 10 secs after the full-throttle switch has last been tripped.

In addition to the valve and control box, a small tub of components is supplied in the VariFlow kit. These comprise two one-way vacuum check valves, two different restrictors, three hose clamps, the micro switch, a small diameter length of steel pipe (used to take the exhaust back-pressure input), a LED and the necessary components to plug into the control box harness plug. You will need to supply your own manual override switch, 5 amp fuse (and holder), electrical cable, vacuum lines and additional hose clamps.

Mounting the Valve

Click for larger image

The VariFlow butterfly can be inserted into any section of your exhaust, however the preferred location is towards the rear of the system. This location has two advantages - it reduces the temperatures to which the valve is exposed and it also allows those noise suppression devices (eg cat converter, muffler, resonator) to be subjected to the set backpressure and so work more effectively. Note that the valve is quite compact (especially when compared to an average muffler) and so it is easy to fit it in place of a factory muffler, or (in the case of the VL Turbo) where the pipe rises to go over the rear axle. The valve has an optimal flow direction and should always be fitted with the actuation canister uppermost to provide better ground clearance.

At the same time as the valve is being fitted, a pressure sensing tapping needs to be made in the exhaust pipe. This is preferably located close to the engine, with the provided short length of steel tube able to be inserted through a drilled hole and then welded into place.

Mounting the Box

Click for larger image

The control box was too large to fit under either of the front seats of the VL and so we decided to mount it in the boot. After it was securely located, the three hoses leading to the control box could be plumbed into place. These comprise the:

  • Engine manifold vacuum feed
  • Exhaust backpressure sensing hose
  • Vacuum control signal to the valve

Rather than running long rubber hoses from the front of the car, we elected to use a pair of 2-metre lengths of 6.5mm ID aluminium tubing, secured along the underside of the floorpan. Rubber hoses were then used to connect the respective ends of these tubes to their destinations. The engine vacuum line needs to have both check valves inserted within it in series, with their flow direction towards the engine. (Two valves are used simply to give better reliability, especially when the system is fitted to turbo cars.)

Click for larger image

The throttle position microswitch was mounted on a small bracket, being located so that it was triggered at throttle angles above 80 per cent. Once that was installed, the dash override switch (and its associated indicator LED) could be put into place, followed by the electrical wiring. For this we used an in-line 5A fuse and picked up a 12V source from an ignition-on circuit.

So how well did it work? That's a story for next week, when we calibrate the system step by step.



Contact:

VariFlow Technology (Australia)
0409 288 347

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Getting planning approval

DIY Tech Features - 7 February, 2012

A New Home Workshop, Part 3

If you do any work with your hands, you need one of these.

DIY Tech Features - 28 July, 2008

Bench Vices

The world's brightest flashing bike tail-lights?

DIY Tech Features - 18 February, 2008

Building a High Performance LED Lighting System, Part 2

Exhaust Gas Recirculation and improving fuel economy!

Technical Features - 20 May, 2008

EGR Comeback

Brilliant information for building tube frame vehicles

Technical Features - 29 June, 2010

Working With Tubular Frames

Quick, easy and effective

DIY Tech Features - 11 January, 2011

Fitting a Short-Shift

DIY timer module adds delays or extended 'on' periods to any electric car function

DIY Tech Features - 1 September, 2008

The eLabtronics Timer

Testing vortex generators on slippery cars

Special Features - 18 October, 2006

Blowing the Vortex, Part 4

Ford in the US says turbo engines will soon be available in nearly all their vehicles - here's the first of the new breed

Technical Features - 14 July, 2009

Ford's EcoBoost Twin Turbo V6

One of the most amazing constructions ever

Special Features - 23 February, 2010

Building the Eiffel Tower

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip