Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Metal Casting, Part 2

Watching a sand mould being made

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Step-by-step of constructing a sand mould for an aluminium casting
Email a friend     Print article
This article was first published in 2008.

Last week in Metal Casting, Part 1 we saw how patterns and sand moulds are made for metal casting. Those patterns (and moulds) varied from being very simple to much more complex, the latter including cores, risers and runners.

This week we’re going to watch a sand mould being prepared from a pattern, the work being done to produce an alloy aftermarket V8 intake manifold. To be able to follow the process, we suggest that you first read Part 1 of this series – otherwise, it’ll be really easy to get lost.

The moulding was being carried out at the Matilda Foundry in Maryborough, Queensland. The Matilda Foundry specialises in small production runs in non-ferrous materials, including aluminium and bronze. We watched owner Neil Anderson at work. Neil has more than 30 years experience in casting.

The sand work for the alloy inlet manifold was made in four parts –

  • the upper mould

  • the lower mould

  • the core for the runners

  • the core for the undercentre

The final result is an amazing three-dimensional jigsaw puzzle!

Click for larger image

The first step was to retrieve the pattern from storage. Patterns are made by dedicated tradespeople called patternmakers. The pattern is critical to the success of the casting, not only in that it needs to create the correctly-shaped final product but also that it need to be able to be withdrawn from the sand mould, be durable, and so on. Some patterns that Neil has seen have been completely unworkable. The pattern was first placed on the joint board; this plane will become the parting line of the mould.

Click for larger image

A removable wooden moulding box surrounds the upper part of the pattern. The part of the pattern that can be seen replicates the top surface of the intake manifold.

Click for larger image

The surface of the pattern was lightly dusted with talcum powder. This allows the pattern to be more easily withdrawn from the sand mould.

Click for larger image

Next Neil filled a container with the special moulding sand. The machine adds the chemical binders to the sand as it is being dispensed. Scales are used so that the correct mass of sand for each mould is dispensed.

Click for larger image

The sand was then poured into the moulding box. At this stage it flows just like normal, fine-grained sand – however it is hardening all the time. Neil suggested that on a hot day, he has to work fast to get the sand properly packed in the mould. Even on this cool day, he still worked fast!

Click for larger image

Using gloved fingers, he carefully packed the sand around the pattern, pushing it into openings and tamping it into place. Sand filled the moulding box almost to the top surface. The assembly was then placed to one side for the sand to go hard.

Click for larger image

The next step was to produce the cores. This is the core box for the undercentre of the mould. It will produce the shaped sand core that prevents metal flowing into the space under the runners.

Click for larger image

Sand is packed into the small cavities of the corebox...

Click for larger image

...and then the corebox is closed and sand is packed into the closed volume.

Click for larger image

The sand core for the intake manifold runners is then produced.

Click for larger image

By this stage, the mould that we saw being formed earlier has hardened, and the mould can be flipped over and the joint board removed. It then looks...

Click for larger image

....like this. Note the circles marked on the pattern – we’ll come back to their function in a moment.

Click for larger image

This side of the pattern is dusted with talcum powder and then...

Click for larger image

...this side of the pattern is boxed.

Click for larger image

The same sand-packing process is again followed, starting with the addition of a measured quantity of sand, followed by....

Click for larger image

..packing and then the placement of brass ‘chills’, located on the previously shown circles. Chills are pieces of metal placed within the mould that promote faster cooling of the casting at these points. This quickens the rate at which thick portions of the casting cool, keeping the overall solidification of the casting occurring at a more even rate. (The chills are later retrieved from the broken sand mould.)

Click for larger image

After the sand has set, the runner core box can be parted, revealing the runner sand core.

Click for larger image

The runner core pattern comes apart (the arrowed parts removed) to allow the core to be withdrawn complete and undamaged.

Click for larger image

The complete sand core for the runners. It’s now much clearer how this shaped sand core represents the ‘induction air passages’ portion of the intake manifold.

Click for larger image

The other core that we saw being made was the undercentre core. This has also now hardened and can be withdrawn from its core box.

Click for larger image

The sand core for the runners is then cleaned up, a small trowel being used to remove the joint fin (the line left by the parting face of the core box) from the core.

Click for larger image

The bottom of the mould can now also be removed, the sand having hardened.

Click for larger image

The bottom surface of the mould, complete with brass chills, can now be seen in its finished form. It needs only to be removing from its moulding box.

Click for larger image

The pattern is then removed from the upper portion of the mould. In this and the above pic you can now see the upper and lower internal surfaces of the mould.

Click for larger image

The underside of the top section of the mould shows four openings. These are for two runners and two risers – that is, where the molten aluminium will be poured in and where it will rise up far enough to nearly overflow.

Click for larger image

The mould and cores can now be assembled. The underside core is firstly placed on top of the lower section of the mould.

Click for larger image

I must admit to getting lost at this point so Neil placed the finished casting (a Funnelweb 2V 351 Ford V8 inlet manifold by Parker Racing) next to the incomplete mould. Looking at this pic, you can see how the underside core (arrowed) represents the lower spaces of the manifold not filled with alloy.

Click for larger image

Next the runner core can be placed into position. Note how this core fits into recesses in the lower mould, so allowing proper registration.

Click for larger image

The mould is then closed by the placement of the upper half of the mould.

Click for larger image

Finally, the mould for the runners and risers is rested on top. It is through two of these holes that next week we’ll see the liquid metal being poured.

Conclusion

As you can see, the complexity of moulds and cores can move very quickly from something as simple as the ‘cotton reel’ shaped casting we saw the pattern and mould for last week, to a sand mould consisting of four separate, interlocking parts. The complexity of a cylinder head mould can only be imagined!

Next week, in the last part in this series, we’ll watch the intake manifold being poured and then the sand mould being broken open to reveal the results.

Thanks to Matilda Foundry for their major help in preparing this series.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Some of the different factory-fitted variable valve timing systems

Technical Features - 26 November, 2002

Variable Valve Timing

The first steam turbine powered vessel - and it was the fastest in the world!

Special Features - 27 July, 2010

The Turbinia

This is what happens when you put a current Merc diesel into a 20 year old body!

Special Features - 12 January, 2010

Mercedes Makeover

How does Hz = stiffness?

DIY Tech Features - 12 November, 2013

Measuring the stiffness of structures by vibration testing

The 1100hp Porsche 917

Special Features - 18 April, 2003

The Early Days of Turbo Part 3

The best shape for inlet pipes

DIY Tech Features - 29 January, 2002

Ballistic Bellmouths

Mixing a dose of LPG with diesel to improve power and economy

Technical Features - 12 March, 2008

Diesel LPG - an Amazing Breakthrough

Fuel cells are being touted by mainstream car companies, but you have to wonder...

Technical Features - 24 October, 2007

Alternative Cars, Part 7 - Fuel Cells

Finding why a V8 Cobra replica was getting hot under the collar

DIY Tech Features - 14 April, 2009

Chasing Overheating

Wrapping-up our brilliant DIY electronic car modification series

DIY Tech Features - 10 March, 2009

How to Electronically Modify Your Car, Part 13

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip