Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

Zero Cost High Tech Interior Lamp

Bright and effective

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Salvaged CCFL from a scanner plus...
  • Salvaged cigarette lighter phone adaptor equals...
  • No-cost and effective interior light
  • Quick and easy hook-up
Email a friend     Print article
This article was first published in 2006.

Click for larger image

If you like collecting the stuff that others throw out, here’s a near zero cost way of putting together a high tech cold cathode florescent light ideal for lighting the inside of boots, under the bonnet or even under the doors.

What You Need

Cold Cathode Fluorescent Lights (CCFL) are used in the instrument panels of some cars like Lexus, but there’s a much easier and cheaper way of getting them. Pretty well all flatbed scanners have them – it’s the light that travels along with the carriage when you’re scanning something. And even in scanners that have been thrown away, the CCFL most often still works.

Click for larger image

The tube – about 2.5mm in diameter and the width of an A4 page (funny ‘bout that!) - is powered by a specific high voltage (HV) power supply unit. But this is usually very easy to locate – it’s the separate printed circuit board with just a handful of components on it that’s connected straight to the CCFL tube. Two wires lead to the HV power supply – a red wire (positive) and a black wire (negative). The CCFL usually lights at voltages above about 5V.

Note: The HV power supply develops hundreds of volts at very high frequency. The high frequency means that it is easy to get skin burns from the supply if you come in contact with it. Be careful!

The CCFL can be run straight off 12V but the tube gets warm and power supply will probably also get hot. Better is to drop the voltage to a more friendly 5 or so volts. This can be done with a high power resistor but a much more elegant way is to use the guts of a cigarette lighter phone adaptor. Many of these produce an output voltage of about 5V and can supply enough current. (Check the markings on the phone adaptor for the actual specs.)

Doing It

It’s a dead easy device to build. Open-up the old scanner and carefully remove the CCFL lamp and its HV power supply. The CCFL lamp will break if bent, so it’s best to keep part of the original housing to hold it securely. If you have a variable voltage power supply, connect up the positive and negative HV power wires and slowly turn up the voltage, checking that the CCFL lights. Bright, isn’t it?

Click for larger image

Then open-up the cigarette lighter phone adaptor, paying attention to which wires are the input (ie nominally 12V in) and which wires are the output (nominally ~5V out). Connect the output wires to the CCFL power supply’s input, maintaining the correct polarity. Solder a pair of wires to the phone adaptor’s input, remembering that the centre pin of the plug is positive.

Check the system works by applying 12V.

Click for larger image

It’s best to mount the HV supply and the phone adaptor in a small plastic box – remember, you don’t want to come in contact with the HV power supply! In our case, the two boards were held in place with double-sided tape.

Click for larger image

Installation is just a case of placing the CCFL in the boot (or wherever you need the light), locating it so that it can’t be knocked. The power supply box can be mounted nearby. Feed power to the system from the original boot light (you can retain that light if you wish, or alternatively replace it entirely with the CCFL) and then wait for darkness so you can admire your handiwork. Wow, a florescent lamp in the boot!

Easy, huh?

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
Want to build your own home workshop? Here's how to begin.

DIY Tech Features - 12 August, 2008

Building a Home Workshop, Part 1

30 cylinders, 21 litres and 470hp!

Technical Features - 25 July, 2008

The Chrysler A57 Multi-Bank Engine

Getting a home workshop to the lock-up stage

DIY Tech Features - 2 September, 2008

Building a Home Workshop, Part 4

The effects of changing dwell time

Technical Features - 26 August, 2014

Ignition coil dwell time

(Relatively) budget mods to a Skyline GT-R

DIY Tech Features - 1 December, 2009

GT-R Revisited

Introducing a breakthrough in DIY electronics

DIY Tech Features - 6 October, 2009

eLabtronics EZ System, Part 1

More low cost aerodynamic testing techniques

DIY Tech Features - 14 April, 2009

Ultimate DIY Automotive Modification Tool-Kit, Part 3

One of the best electronic car modification tricks you ever saw

DIY Tech Features - 15 October, 2013

Pots aren't just variable resistors

How good were they?

Special Features - 15 June, 2010

The First Holdens

Drive a diesel? Find out when to change gear for best performance!

DIY Tech Features - 22 January, 2008

Finding the Best Gear Shift Points

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip