Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

The Intelligent Turbo Timer

It sets the idle-on time automatically

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Cheap electronic kit, also available pre-built
  • Intelligently matches idle-on time to way you've been driving
  • Adjustable sensitivity
  • Adjustable maximum idle time
Email a friend     Print article
Click for larger image

Especially if your turbo car is driven by other people, a turbo timer is a great idea. It lets the car idle for a short time after you’ve come to a stop and switched off the ignition, so cooling down the turbo bearing and preventing the oil overheating through heat soak. In addition, it also lets the exhaust manifold - and the rest of the engine - come back down to sane temperatures.

But the trouble with a normal turbo timer is the idle-on time is pre-set. So whenever you turn off the car, the engine will run for 15 seconds, 30 seconds or a minute – whatever you have the timer set for. Even if you have only driven gently around to the shop, the turbo timer will keep the engine running. Sure, most turbo timers have a cancel switch, but it’s a pain to always have to press the button.

Click for larger image

But the Intelligent Turbo Timer is different. Instead of simply always idling the car for a pre-set period, it actively watches how you are driving in the kilometres before switch-off. If you’ve been fanging the beegeezus out of the car, it will idle the car for a longer period, but if you’ve just been driving gently, it won’t idle the car at all. And it can pick any idle-down time in between.

It also does all of this automatically – all you need to do is fit the Intelligent Turbo Timer, set it up for the sensitivity that you want, and then forget it.

The Way It Works

In addition to having connections for a heavy current automotive relay to bridge the ignition key contacts (that’s the way all turbo timers keep the car running after you’ve switched off), the Intelligent Turbo Timer also has a signal input. This voltage signal can be from an airflow meter, a MAP sensor or even the throttle position sensor. (And in cars without engine management, it can use the input from an added boost pressure switch connected to 12V.) The only requirement is that this signal input voltage varies with engine load.

Note that the connection of the turbo timer won’t have any affect on the sensor output – it will continue to work with the engine management system just as it did previously.

The Turbo Timer watches this voltage signal and when it rises above a certain level (called the ‘threshold’), it knows the engine is being driven hard. The Turbo Timer then monitors how long in the 7 minutes before the ignition was switched off the engine load was higher than the threshold. The idle-on time is set on this basis.

To tune the application of the Turbo Timer, the voltage level at which the threshold is adjustable, as is the maximum time the engine can ever idle for.

Let’s take a look at those two adjustments in more detail.


Click for larger image

The threshold is set by a multi-turn pot. The input signal range can be anything up to ~12V, and can be a signal that rises with load (most common) or falls with load. (The selection of ‘rising’ of ‘falling’ is made with a link on the board.) Setting the threshold is easy because a LED on the board lights when the threshold is exceeded. So setting up this function is just a case of driving the car and turning the pot until the LED lights when the car is being driven hard.

Click for larger image

The maximum idle-on time is set by a rotary switch, which is marked 0-9 and A-F. Each position corresponds to a maximum idle-on time – for example, position 1 is 30 seconds and position 8 is 4 minutes. Note these are the very longest times the car can ever idle for – in normal driving, the maximum time is very seldom reached. The shortest time available is 15 seconds and the longest, 15 minutes.

Other Features

The Intelligent Turbo Timer also has a reset switch that can be placed on the dash. This switch should very seldom be used but it’s included in case the engine needs to be switched off in an emergency. A LED also lights during the idle-on time – this can be mounted at the timer or remotely. Finally, there are also output connections for another relay, which may be needed with some security systems.


At its simplest, only four wiring connections are needed to install the Intelligent Turbo Timer. These are:

  • Earth
  • Battery side of the ignition switch
  • Ignition side of the ignition switch
  • Engine load sensor

It’s easiest to make the ignition switch connections near the switch. Use a multimeter to locate a wire going to the ignition switch that always has battery voltage on it. Then turn the ignition key to the ‘ignition’ position and find another wire that has battery voltage on it only when the key is in this position. That is, when you turn the switch off, the power on this wire disappears. Tap into these two cables and connect them to the correct spade terminals on the Turbo Timer.

The 12V wire on the battery side of the ignition switch always has 12V on it! This means you should be very careful that this wire cannot contact ground – if it does, at minimum you will blow a fusible link and at worse, start a fire.

In addition to telling the Turbo Timer whether the ignition key is turned on or off, these ignition connections also supply +12V to the timer. The earth connection can be made to any convenient chassis point.

Click for larger image

The engine load sensor input can be found by using a multimeter to back-probe the airflow meter (or MAP sensor, etc) until a wire is located that has a voltage on it that varies with engine load. Again the wire doesn’t need to be cut – the Intelligent Turbo Timer engine load sensor wire just T’s into it. This connection can be made either at the sensor or at the ECU.


Set-up involves turning the multi-position switch to select the maximum idle-on time you’ll ever want, and then adjusting the sensitivity of the threshold setting to give the idle-on time that best suits your needs. You should leave the board accessible for a few days while you fine-tuned the action of these settings.


Over the years, we’ve often derided turbo timers as a waste of money. However this one doesn’t cost much and only ever provides the required idle-on time. And that’s a turbo timer that makes sense...

The Background Story

So how did this kit come about?

The Intelligent Turbo Timer was developed and designed by Silicon Chip [] electronics magazine. The kit, along with many others, is covered in the Silicon Chip publication, High Performance Electronics for Cars. The book is a must-have for DIY modifiers. The kit for the Intelligent Turbo Timer is available from Jaycar Electronics [] or through the AutoSpeed shop .

The electronics design and development of the Intelligent Turbo Timer was carried out by electronics engineer John Clarke, while I came up with the concept and did all the on-car development. (During this period I wore a different hat to an AutoSpeed contributor, working for Silicon Chip Publications as a freelance contributor to High Performance Electronics for Cars.)

So by no means should the Intelligent Turbo Timer be seen as an AutoSpeed-developed project, at the same time I am happy that AutoSpeed endorses it and promotes it.

Julian Edgar

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
Is it worth producing your own fuel?

Special Features - 4 March, 2008

Making Your Own Bio-Diesel

What are the risks and benefits?

Special Features - 6 August, 2013

Children and home workshops

Country driving skills have almost disappeared - here are some

Special Features - 4 October, 2011

How Not to Die this Week

Building a programmable temperature alarm

DIY Tech Features - 13 October, 2009

eLabtronics EZ System, Part 2

A different electric fan

DIY Tech Features - 9 June, 2009

Chasing Overheating - Again!

Measuring ride quality

Technical Features - 4 May, 2010

Ride Quality, Part 2

Aerodynamic testing techniques for near zero cost

DIY Tech Features - 7 April, 2009

Ultimate DIY Automotive Modification Tool-Kit, Part 2

A brilliant do-it-yourself handheld spotlight or bike headlight

DIY Tech Features - 11 February, 2008

Building a High Performance LED Lighting System, Part 1

Some of the different factory-fitted variable valve timing systems

Technical Features - 26 November, 2002

Variable Valve Timing

How to get the best out of a bench grinder

DIY Tech Features - 8 July, 2008

Using Bench Grinders

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip