Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

Building an Electric Bike, Part 2

Attaching the new driveline

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Part 2 of a 3-part series
  • The electric motor
  • The drive system
  • Gearing
  • Motor mounting and cooling
Email a friend     Print article
This article was first published in 2005.

Last week we introduced you to the design of our DIY electric bike (Building an Electric Bike, Part 1). We showed you how you could add electric power to a normal bike and the simple control system that allows both performance and regenerative braking modes. (If you’re coming to this article first, it won’t make much sense without starting at the beginning of the series!) This week we build the bike, starting with the motor.

The Motor

In this design, the motor cops a caning. But the approach works very, very well. Cheap, too. Basically, what we do is to use an excellent quality, nominally 12V motor - and often run it at 24 volts!

Aaaagghhhhhh! I can hear all the design engineers sputtering. You may get theoretically four times the power, but what about the heat? What about the bearings? What about....? Three points. The first is that data-logging the current flow to the motor shows that typically it’s drawing less than it would under high loads on 12V. Secondly, when it is drawing very high currents, it’s usually only for a short time. And the third point? We dramatically improve the motor’s cooling.

Click for larger image

The motor that’s used in the bike is from a Honda electric power steering system. More and more small cars are running electric power steering and the motors are beautifully made, high torque designs. As said previously, the motor shown here was sourced from the tip (the complete electric steering rack was a warranty cast-off from a Honda dealer - no, I’ve never been able to find what’s supposed to be wrong with it) but similar motors can be obtained from Japanese importing wreckers. When looking for a motor, aim for an ‘orphan’: a steering rack imported with perhaps the front half of a car - the engine in the half-cut suitable for local models but the electric steering rack an unknown.

Heavy duty windscreen wiper motors and hydraulic brake boosters are alternative sources of motors - again, you don’t want to request a specific part but instead see if you can find an unwanted one. Look for heavy gauge wiring going to the motor - the thicker it is, the better

In most cases, the output shaft of these motors uses a worm that drives a spur gear. What we do is cut away part of the output gearbox casting so that the worm itself can be pressed against the tyre tread. (In fact we replace the worm with a roller but we’ll come back to that in a moment.) So in addition to looking for a good quality 12V motor, also assess the shape of its output housing. It’s even better if the shaft is supported at both ends with roller bearings, but in some cases only plain bearings (eg bronze bushes) are used.

If you do score an electric power steering motor, there’s another advantage - many have an electric clutch built into the assembly. Disconnect power and the output shaft turns freely; apply power and the shaft is locked to the motor. This function gives better motor-off performance as the bike wheel is spinning just the roller and a short section of shaft, rather than driving the whole motor.

Lifting the Roller

In the case of the bike shown here, the motor assembly has a built-in electric clutch. With the clutch wired in parallel with the motor, switching off the motor enables the output roller to freewheel. However, most motors won’t have this function and it may be advantageous to add a mechanism that allows the rider to operate a lever to pull the roller up off the tyre. As the motor assembly can be moved upwards against the spring tension, this is easily achieved

The Roller

Either by unbolting an extension housing or by pulling the armature out of the motor, you should be able to gain full access to the worm. Originally, I created the roller by forcing heavy-duty rubber hose over the worm. This was quiet and initially effective, but once the hose-roller got hot, the rubber was quickly destroyed.

(I should add at this point that the prototype was [and is] subjected to bicycle torture: the hills around here have very steep gradients of up to 17 per cent and when I started this project, I hadn’t ridden a bike frequently for a very long time. So the motor was required to do a lot of work...)

On the flat, the rubber hose roller may last very well - and it’s certainly the easiest way of turning the worm into a roller that can bear against the tyre tread. However, in this case, a metal roller had to be placed over the worm. While initially I thought it would be a requirement that the roller be knurled (ie have ‘grip’ marks machined into it), the friction between even a smooth roller and the tyre is OK - especially on flat roads.

Click for larger image

How you turn the worm into a metal roller is up to your ingenuity - I ended up using a drilled-out 10mm deep-style socket surrounded by a roller salvaged from the output shaft of a stepper motor. The roller was slipped over the top of the socket, being held in place with a grubscrew.

Click for larger image

However, when I realised I just loved riding this electric bike, I decided to remove my (relatively) bodged-up roller and have a small machine shop turn-up a new shaft, complete with knurled roller. This cost AUD$140.

Chain Drive?

Lots of home-brew electric assist bikes use wheelchair or automotive windscreen wiper motors, complete with the worm drive gearbox. Typically, the output gear drives the chain. However, a downside of this approach is that regenerative braking cannot occur - very few worms will drive backwards.


The relationship between the ‘natural’ speed of the motor, the available motor power, and the diameters of the roller and the tyre will determine the on-the-flat cruising speed.

There are far too many unknowns to even make a guess as to what the gearing outcome will be - testing is the only way. With the bike shown here, the diameter of the roller on the output shaft is about 25mm and the tyre is nominally a 26-inch design. This gives an on-the-flat cruise speed of about 18 km/h - or 20 km/h with just very gentle pedalling. This speed works really well on the road - not too fast to attract attention but quick enough to get places. (After all, 20 km/h averaged for an hour gets you 20 kays away!)

Click for larger image

If the on-the-flat cruising speed is too slow, increase the diameter of the roller. If it is too fast (or more likely, your hill-climbing ability is really bad), decrease the diameter of the roller. Changes in roller diameter are easily tested by using different diameter rubber hoses - even if the roller life is short, it will give you a guide to the outcome.

Note that mountain bike knobbly tyres should be replaced with smooth highway tyres - they’re available for wide mountain bike rims but you might have to scout around a few shops to find them.

Variable Gearing

If you want to get very tricky, it’s possible to replace the cylindrical roller with one shaped like a cone. If the motor and cone-shaped output roller are moved laterally across the tyre, the gear ratio of the drive system can be steplessly varied.

Motor Mounting and Cooling

Click for larger image

The motor’s output roller needs to be held rigidly at right-angles to the tyre tread. Further, it needs to be pushed down into the tyre so that the tyre and roller have a good frictional grip on one another. It also helps if existing holes in the bicycle frame are used.

In this case, 40mm square, 3mm wall aluminium tube was used to form a T-shaped frame that held the motor in place in the right position. The motor is attached to the frame using long heavy-duty plastic hose-clamps and is preventing from swivelling by 50 x 3mm aluminium angle. (It’s easier to look at the pictures than read a description!)

The roller pressure on the tyre is maintained by the use of an extension piece of smaller aluminium tube that goes to the underside of the seat, a threaded bolt and a stiff compression spring.

Click for larger image

Lots of testing showed that the motor could get really hot after long, very steep hills. (In these conditions the bike speed is down to 10 km/h or so and I’m pedalling in 1st or 2nd gear of 21 speeds.) To stop the motor getting so hot, a cooling air scoop was then added. It’s made from a 75mm stormwater pipe plastic elbow that was cut, heated and bent to form the required shape.

Click for larger image

The scoop dropped moving motor temps a lot but if the bike was stopped after climbing a long hill (or descending it, where regen braking loads the motor), the external casing rose in temp to 55 - 60 degrees C. To stop this temp increase, a PC cooling fan was integrated into the scoop. It runs off just one of the 12V batteries (its current load is tiny) and is triggered by a thermostatic switch mounted on the motor. The fan comes on at 57 degrees C and switches back off at 48 degrees C. The switch was salvaged from a dishwasher.

On hot days the fan operates when the bike is moving, but in most cases it switches on only when the bike has come to stop. In this situation it runs for 10 or so minutes.

Next week: the batteries, and riding the bike!

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
Beautiful and sophisticated, but was it a technological dead-end?

Special Features - 30 June, 2009

The NS Savannah

Drives like a big engine... but drinks like a little one! How do you achieve that?

Special Features - 23 March, 2010

The Confidence Trick

Testing vortex generators on slippery cars

Special Features - 18 October, 2006

Blowing the Vortex, Part 4

Getting a new intercooler connected

DIY Tech Features - 26 July, 2011

DIY Intercooler Plumbing

Do-it-yourself aero testing of an Impreza WRX

Technical Features - 23 June, 2007

Aero Testing, Part 2

A brilliant do-it-yourself handheld spotlight or bike headlight

DIY Tech Features - 11 February, 2008

Building a High Performance LED Lighting System, Part 1

A brilliant new temperature controller that's so cheap it's unbelievable.

DIY Tech Features - 15 November, 2011

$25 Temperature Controller and Display!

Squirt your intercooler spray for 5, 10 or 20 seconds - all at the press of a single button!

DIY Tech Features - 2 September, 2008

Intercooler Spray Squirter

Form beads in aluminium, steel and stainless steel intercooler plumbing

DIY Tech Features - 11 February, 2014

Make your own tube beader

Got a 'PD' VW / Audi / Skoda / SEAT diesel? Changing the cam timing can make major differences to performance and economy.

DIY Tech Features - 23 August, 2011

Big Changes from Tiny Adjustments!

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip