Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us

Hydroforming - Part 1

A new way of forming metal into complex shapes.

Courtesy of Schuler Hydroforming GMBH & Co

Click on pics to view larger images

This article was first published in 2001.
Click for larger image

If you've looked carefully under a late model car you may have seen an intricately curved engine subframe that is quite unlike previous pressed and welded designs. Or, you may have marvelled at the superb bending of the exhaust header tubes on a BMW M3. Or looked with puzzlement at the inner bumper steel pressing on a Ford Mondeo. How have they formed the steel so seamlessly into such an intricate shapes? The answer is - hydroforming.

Hydroforming is the expansion of tubular metallic tubes by internal water pressure in a closed die. In general the die is opened, closed and maintained in its closed position by a hydraulic press.

The Process

1. Close die

Click for larger image

The starting tube - a straight or pre-bent tubular section - is placed into a die which has the contour of the component to be produced.

2. Fill with water

Click for larger image

The die is closed and held closed by means of a hydraulic press. Hydraulically actuated sealing punches close off the tube ends and fill the tube with the fluid medium, thus building up internal pressure

3. Start hydraulic press, regulate water pressure

Click for larger image

In the actual forming process the material is expanded by the internal water pressure. At the same time the sealing punches compress the tube ends. This causes the material to flow into the contour of the die. Precise control of the internal pressure and of the axial cylinder movement enables the material to take on the form of the internal die's contour.

4. Open press, unload component

Click for larger image

Hydroforming completed, the hydraulic press opens the die and the component can be unloaded.

Starting material consists of pre-bent or otherwise pre-formed metallic hollow sections. By the means of hydroforming, hollow bodies of complex geometries can be achieved, which with other processing methods could only be produced in multiple parts. The special features of hydroformed components are consistent high tensile strength and rigidity, optimised weight and accurate geometry.

Cycle times of hydroform processes typically range between approximately 14 to 40 seconds. The essential factor of a hydroform process control is the co-ordination of the individual process parameters with each other. Too high an internal pressure may cause bursting. If, on the other hand, the internal pressure is too low, the part will form wrinkles.

Hydroforming equipment, in general, consists of the following components:

  • Hydraulic hydroforming press,
  • Hydroforming unit with hydroforming water system (tank, pumps, valve units, filters for the forming fluid) and pressure intensifiers,
  • Control and regulating techniques consisting of elements to operate the press, the hydroform water system and to control the forming process.

In principle, all materials suitable for other cold forming processes, eg deep drawing, can be used for hydroforming. These include:

  • Construction and auto body steels
  • Aluminium and its alloys
  • Heat resistant and stainless steels
  • Copper and its alloys
  • Titanium and its alloys

Next week - hydroforming may allow automotive spaceframes to make a comeback.

Case Study
Click for larger image

For the new Volvo 2.8 litre V6 motor, Schuler Hydroforming and the Volvo Car Corporation have developed fresh air suction pipes and turbo high pressure pipes using hydroforming. The special features of these components are their low weight and the reduced number of parts. The alternative to hydroforming was to use the traditional mix of rubber, silicon and aluminium parts linked with hose clips. However, taking this approach gave higher internal pressure losses - up to 22 kPa. Another approach could have been to use sand-cast tubes, however this gave higher weight and required the expensive cleaning of components The internal pressure loss of the hydroformed components was only 10 kPa.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
A dozen bits to find at the truck wreckers.

Technical Features - 29 August, 2008

Junkyard Dawg

Is it worthwhile tuning an engine cylinder by cylinder?

Technical Features - 4 February, 2008

Cylinder-Specific Tuning

DIY timer module adds delays or extended 'on' periods to any electric car function

DIY Tech Features - 1 September, 2008

The eLabtronics Timer

Not just the largest aircraft made of wood, but also with incredible underskin technology

Special Features - 29 September, 2009

The Spruce Goose

Clearing the space

DIY Tech Features - 10 January, 2012

A New Home Workshop, Part 1

...but it never turned a wheel in anger

Special Features - 8 April, 2014

The fastest Mercedes of them all?

Perhaps the most sophisticated human powered vehicle you've ever seen

DIY Tech Features - 17 December, 2007

Air 150 Recumbent Trike, Part 1

Easy, cheap and effective

DIY Tech Features - 30 April, 2013

Building a home sound amplifier, Part 1

Installing lights in a home workshop

DIY Tech Features - 16 September, 2008

Building a Home Workshop, Part 6

A new engine designed to extend the range of plug-in hybrid cars

Special Features - 8 December, 2009

The Lotus Range Extender Engine

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip