Magazines:  Real Estate Shopping: Adult Costumes  |  Kids Costumes  |  Cars  |  Guitars |  Electronics
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Going Direct Injected Turbo Ethanol!

The advantages of small boosted engines running direct injected ethanol

Courtesy Ricardo

Click on pics to view larger images


This article was first published in the Ricardo Quarterly Review. It is used here with permission.

Downsizing in combination with boosting and direct injection of a spark ignition engine has benefits, especially when that alternative fuel is ethanol. Technology company Ricardo has been investigating.

Click for larger image

There is a big push to use alternative fuels in the US, says product group director for gasoline, Rod Beazley, at Ricardo Inc. in Detroit.

"But ethanol has both good and bad attributes. A good one is that it has a very high octane rating, but most flex-fuel vehicles are not optimised for that. By exploiting that high octane rating we can reap huge benefits and can downsize a light truck engine from a 6.6-litre diesel to a 3.2 litre spark-ignited engine running on ethanol.”

Beazley and his team are currently engaged in a project in this area known as Ethanol Boosted Direct Injection (EBDI), being carried out in collaboration with Behr, Bosch, Delphi, Federal Mogul, Grainger & Worrall Castings and Honeywell. In February, Ricardo announced the initial test bed results of the first prototype engine using this highly promising technology.

Normally a conflict

With normally aspirated, flex fuel, spark ignition engines, there's a conflict of interest between burning gasoline with an octane rating of less than 100, and ethanol, whose octane rating is around 110. A compression ratio high enough to exploit ethanol properly would be unfeasibly high for pump gasoline. But with a boosted engine, cylinder pressures can be controlled using boost and valve control, while the mechanical compression ratio remains at conventional levels.

“It's applicable to many different areas, including agriculture and medium-duty applications, that have traditionally used compression ignited [diesel] engines," says chief engineer Luke Cruff.

"It really depends on how much downsizing you can get away with. In this case we are powering an 80001b [3.63 tonne] truck with a 3.2-litre engine which is a much higher level of downsizing than current convention."

High-efficiency energy conversion

Downsizing means finding systems that deliver high-efficiency energy conversion. Because current systems are not fully optimised for ethanol and gasoline, not only is the full power and torque potential not realised when burning ethanol, but fuel economy is poor, too.

However, EBDI solves many of the challenges faced by flex-fuel engines because it is optimised for both alternative fuels and gasoline.

When operated on ethanol blends such as E85, current flex-fuel engines pay a fuel economy penalty of about 30 per cent compared to gasoline. The EBDI engine substantially improves ethanol's efficiency, and performs at a level comparable to a diesel engine.

As Cruff explains: "You can close the heating value gap between gasoline and ethanol by running at higher loads, more often.”

“Octane is a positive attribute, and ethanol also has a high latent heat of vaporisation, so when you spray it into a cylinder you get better charge cooling. As far as knock is concerned, it's a win win situation. Knock is inhibited by both the octane rating and the charge cooling.”

Click for larger image

A combination of variable valve timing and lift, and clever manipulation of engine boost, can deliver an equivalent effect to variable compression ratio in a naturally aspirated engine. But the high pressures involved some physical engine modifications, says Cruff.

"To take full advantage of this system the engine has to withstand much higher cylinder pressures than usual. So high, in fact, that diesel and spark ignition engines start to look pretty similar, with engine speeds reducing to 5000 rev/min on the EBDI spark ignited engine. You could potentially start with a diesel engine as a basis and convert it to spark ignition.”

The prototype EBDI engine is based on a standard direct injection, 3.2-litre V6 direct injection engine: the team modified it to withstand cylinder pressures of 180 bar rather than the usual 120 bar.

“Although we made some substantial modifications," Cruff explains, "we didn't do anything to change the architecture such as increasing the number of cylinder head studs."

Independent research conducted by Ricardo, outside the scope of the technical collaboration, indicated that hardware costs compare well with diesels.

Ricardo estimates that the EBDI fuel system would cost in the region of $300 to $400: this compares with $2,000 to $2,500 for a typical diesel. The position with aftertreatment is similar. A diesel system costs in the region of $1,500 to $2,300, while EBDI runs using a standard three-way catalytic converter costing a fraction of the price of state-of-the-art diesel systems.

Twin turbos

Turbocharging is achieved by parallel turbochargers of equal size and, at least for the purposes of the research programme, fixed geometry.

"There are many different ways of configuring the boost system for a production engine," explains Cruff. "But at this stage, we were mainly interested in the combustion system.”

Emissions targets are the current Federal Bin 5 or Californian ULEV 11 levels but EBDI promises huge benefits, not only in terms of sustainability but also cost.

The future for ethanol fuel in North America and Europe is likely to be production from cellulosic feedstocks to avoid competition with foodstuffs and to increase the potential volume.

In real-world terms, the efficiencies of this form of fuel production means that EBDI can potentially reduce the actual cost of transportation when compared to fossil fuels, and can do so based on a renewable fuel resource. Moreover, with estimates of the long-term cost of cellulosic ethanol production as low as $1.50 per US gallon and with the recent history of wide fluctuations in prices, a painful experience for many, EBDI's multiple fuel optimised capability could be a particularly attractive future powertrain technology.

Click for larger image

With initial testing now complete, the EBDI research team will focus both on test bed optimisation and on developing a vehicle based demonstrator. This will be based on a dual-wheel pick-up truck and is intended to be available for testing later in 2009.

In summarising, Beazley emphasises the sheer scalability of EBDI and its potential reach far beyond the automotive and light-truck industry.

"Imagine agricultural equipment that, in effect, burns what it harvests - corn, sugar cane or some other renewable substance. It could mean tremendous cost savings across many industries."

With its inherent highly optimised fuel-flexibility, and its impressive fuel economy, EBDI technology could well provide a green future that could pay dividends too - in more than one sense.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Do-it-yourself aero testing on the road!

Technical Features - 13 June, 2007

Aero Testing, Part 1

Finding the best location for engine bay vents

DIY Tech Features - 10 June, 2004

Undertrays, Spoilers & Bonnet Vents, Part 3

Measuring ride quality

Technical Features - 4 May, 2010

Ride Quality, Part 2

The advantages of small boosted engines running direct injected ethanol

Special Features - 16 June, 2009

Going Direct Injected Turbo Ethanol!

A very cheap workbench for your power tools

DIY Tech Features - 5 February, 2013

Building a power tool workbench

Using a prebuilt DIY electronic module to flash high intensity LEDs

DIY Tech Features - 14 July, 2008

Bike LED Lighting Power!

Debunking untruths

Special Features - 1 September, 2009

Automotive Myths

Wrapping-up our brilliant DIY electronic car modification series

DIY Tech Features - 10 March, 2009

How to Electronically Modify Your Car, Part 13

How to use hand tools for best results

DIY Tech Features - 4 August, 2007

Using Hand Tools - Spanners and Sockets

Watching an aluminium intake manifold being poured

Technical Features - 2 December, 2008

Metal Casting, Part 3

Copyright © 1996-2014 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip