When in 1997 DaimlerChrysler was evaluating future
engine directions, the company realised that the then-current 5.9-litre V8 used
in US market trucks was likely to be outgunned in performance and economy by
coming competitors. Studies were made of possible replacement designs, including
iterations with 2, 3 and 4 valves per cylinder, overhead valves and overhead
camshafts, the latter including single camshaft and double camshaft designs.
However, in the end, the company chose a
2-valves-per-cylinder, overhead valve, hemispherical combustion chamber
approach. The 5.7-litre Hemi was introduced for the 2003 model year Ram series
of pick-up trucks.
So what makes this engine better than the engines
of 20, 30, and 40 years ago that the specifications appear so similar to?
New Design Aims
DaimlerChrysler engineers had these aims for the
- engine performance
- noise/vibration/harshness (NVH)
- reliability and serviceability
- leak free
- fuel economy
- exhaust emissions
- mass reduction
- "no touch"
- reduced part count
The 5.7-litre engine that resulted was an OHV
90-degree V8 using an iron block and aluminium cylinder heads. Each of the
hemispherical combustion chambers featured two spark plugs and two valves. The
intake manifold used a composite (plastic) construction. Maximum power of 257kW
was developed at 5600 rpm and a peak torque of 508Nm was available at 4400 rpm.
Despite that relatively high peak torque rpm, the big engine developed 412Nm at
just 1200 rpm. Mass of the engine was 242kg.
But let's have a look at the design in more
The block was cast from simple grey cast iron. It
used a dry valley and deep skirt design, with the cam mounted high (for an OHV
engine!) in the block. Potential leak sources through welch plugs were
eliminated - the water jacket of the block didn't have any. As a result of this
approach, the open-deck block required large openings for easy sand removal after
The main bearing caps were made from powder metal
and used cross-bolting with a single M8 bolt each side. A 99.5mm bore and a
90.9mm stroke were used, with a bore spacing of 113.3mm.
Extensive use of Computer Aided Engineering (CAE)
was made in the design of the block, primarily in order that it be made as light
as possible while still being cast from iron. In addition, the "no touch" goal
was addressed - this referred to a manufacturing process that prevented any
finished surface from being touched once it had been machined or ground.
The heads were cast from A319F aluminium alloy and
each had a mass of approximately 13.6kg, a substantial 9kg reduction over the
previous 5.9-litre engine. The heads were bolted to the block using M12 bolts
spaced around the bores and M8 bolts near the intake manifold. Intake valves
were 50.8mm in diameter and exhaust valves, 39.4mm. The intakes were angled at
18 degrees relative to the head surface, while the exhaust valves were at 16.5
degrees. The valve seats and valve guides were made from powdered metal.
Intake and exhaust flows were comprehensively
tested and on the inlet reached 118 litres/second (at 6.2 kPa pressure
differential) at 12mm of valve lift, and on the exhaust, 85 litres/second at the
same lift and pressure differential.
The valve bridge was kept wide in order that
adequate cooling flow could be maintained; this was seen as especially important
in the truck applications of the engine where it could be expected to be working
hard for long periods.
To reduce the likelihood of leaks, the spark plugs
were mounted in cast-in towers. A previous design approach used pressed-in spark
plug tubes but the chance of leakage occurring past the seals was seen as too
CAE was used to optimise the coolant flow within
the heads, which was primarily a 'U-flow' beginning at the rear of each head and
exiting at the front into the cylinder block. Using Computational Fluid
Dynamics, fillets and ribs were added to the internal head coolant passages in
order that higher velocity flows occurred in critical cooling zones.
The cylinder head gaskets were three-layer
stainless steel with a compressed thickness of 0.7mm.
The front cover, which sealed the front of the
block and sump, was die-cast from SAE A380 aluminium. The alternator, water
pump, air-conditioning compressor, power steering pump and belt idler were all
mounted on the cover. Careful design achieved lower levels of vibration for the
mounting points of the air-conditioning compressor and alternator.
The water pump was also die-cast from SAE A380
alloy. It used an internal coolant bypass and an 89mm diameter, fully-shrouded
The intake manifold assembly comprised a
pre-supplied module containing the injectors, an 80-mm diameter electronic
throttle butterfly, intake manifold, sound-damping cover, the PCV system, MAP
sensor and engine wring harness. With all these components integrated into the
one unit, over the previous engine design the final assembly part count
decreased from 26 to 2.
The intake system, made from seven sub-assemblies
formed from Nylon 6, used an 11.3 litre plenum volume and intake runners that
were each 273mm long. Each runner tapered from a diameter of 50mm at the plenum
to 43mm at the heads. The intake plenum volume was kept low to "achieve
excellent throttle response and minimise idle speed variation". When compared
with intake port flow alone, the intake system caused a 10 per cent flow
restriction at maximum power.
To reduce NVH, the intake assembly used a
3-chamber Helmholtz intake resonator (see
extensive ribbing and a minimum 3mm wall thickness on all exposed surfaces. A
soundproofing pad was also attached to the base of the assembly, across the
Despite looking quite basic, the engineers claimed
that the exhaust manifolds were the result of extensive and detailed design.
Each was designed to provide maximum flow capacity within the constraints of
taking up minimal room, protecting under-bonnet components from heat, and having
a low thermal inertia so that the cat converters could be quickly heated. The
claimed life of the manifolds was 241,395km. (At 241,396km they crack?!) The
manifolds were cast from high silicon-molybdenum ductile iron; when compared
with 4-2-1 extractors, the manifolds reduced peak power by only 2.2 per cent.
A geroter style pump, driven from the timing chain
crankshaft sprocket, provided oil flow to the lubrication system. The pump was
made from die-cast aluminium (housing), powdered metal (geroters) and cast iron
(cover plate). It displaced 1.1 cubic inches per revolution and was sized to
allow for "future oil system controlled devices" (perhaps variable cam timing or
variable cylinder cut-off), worked at a relief pressure of 55 psi and used 5W-30
oil. The oil capacity was 7 quarts; smaller volumes created aeration problems at
The crank was cast from nodular iron. It used main
journals that were 65mm in diameter, with the small-end journals 54mm. The
design included deep-rolled undercut fillets to improve fatigue strength. A
vibration damper was a press-fit on the nose of the crank; no keyway was used as
part of the 'leak-free' design goal.
The con-rods were manufactured from powdered metal
and featured cracked big-ends. Each rod had a mass of 597 grams (including the
bolts) and was controlled such that no rod varied from this figure by more than
plus/minus 5 grams.
The pistons were cast from eutectic alloy and each
had a mass of 413 grams. Each slightly domed piston was coated with a graphite-based product on the skirts to reduce scuffing. The top land was reduced to 3mm
to minimise crevice volume and so hydrocarbon emissions. The gudgeon pin was a
press-fit in the con-rod.
It is significant that despite starting with the
proverbial 'clean sheet of paper', DaimlerChrysler engineers decided to go with
a design that was very conventional in its engineering fundamentals. The
engineers saw the advantages of the 5.7-litre Hemi design as:
- Class-leading performance with 41 per cent more
power, 46 per cent greater power density and a torque increase of 12 per cent
over the previous design
- Competitive fuel economy, high combustion
stability and low specific exhaust emissions
- Highly integrated intake manifold
paper 2002-01-2815: The New DaimlerChrysler Corporation 5.7 HEMI V8 Engine
Hemis of the Past
The 5.7-litre is the fifth OHV Hemi Chrysler V8.
Here are the previous designs:
Chrysler Fire Power V8
DeSoto Fire Dome V8
Dodge Red Ram V8
The detail in the comparison between the '66 426
and the new 5.7-litre show some startling changes, even in the basic
1966 426 HEMI
Bore Spacing (mm)
Bank Offset (mm)
Block Length (mm)
Block Deck Height (mm)
Connecting Rod Length (mm)
Piston Compression Height (mm)
Rod Length/Crank Radius
Intake Valve Diameter
Exhaust Valve Diameter (mm)
Included Valve Angle (deg.)
Combustion Chamber Volume (cc)
Intake Valve Lift (mm)
Exhaust Valve Lift (mm)
Courtesy of DaimlerChrysler, Some Hemi-Powered
1955 CHRYSLER 300
With a HEMI® engine mated to the new
Powerflite automatic transmission, styling by Virgil Exner, plus power steering
and power brakes, Chrysler product planners realized they had the ingredients
for a car that in Italy would be called a Gran Turismo - a sport tourer. Despite
a two-ton body and a luxurious cabin, a stock 300 powered by its 300 hp dual
four-barrel, 331 c.i.d. HEMI® could nudge 125 mph. The Chrysler 300 was a
performance blueblood from the beginning and is highly sought by collectors
1957 PLYMOUTH "SUDDENLY,"
THE HOT ROD MAGAZINE SPECIAL
When NASCAR introduced a new "Experimental"
class for its Speedweeks at Daytona Beach in 1957, Wally Parks, co-founder of
both Hot Rod Magazine and of the National Hot Rod Association, decided he'd
play, too. Although the class was intended primarily for company-backed entries,
Parks, then editor of Hot Road Magazine, and the magazine's technical writer Ray
Brock "borrowed" a new Plymouth Savoy right off the line at Chrysler's Los
Angeles plant. The name came from the Plymouth ad campaign at the time,
"Suddenly It's 1960!"
A Chrysler HEMI® was modified to 389 c.i.d. and
special exhaust headers added. Firestone racing tyres, roll bars and safety
equipment were installed and the front end modified. Towed to the starting line
at Daytona, it had never run under its own power. Nevertheless Parks hit 166.898
mph, and the two-way average over two miles was 159.893 mph! This was the
fastest time run for the week, and was then the fastest closed-car run ever
recorded at Daytona. In the process, Plymouth beat 13 other makes. Later that
year, with a new HEMI® from Dean Moon, Ray Brock got the Plymouth to 183 mph at
After being reconverted to street use, the car was
sold and disappeared. In 1995 Parks, then age 83, decided to recreate
"Suddenly," but the body used was not a hardtop, which Parks felt was not
authentic. Brock then gave him a hardtop as a birthday present and it became the
source of the correct "postless" body. Parks has run "Suddenly II" a number of
times in exhibition competition.
1967 GOULET & DENOBLE "PROBE" AA/FUEL
1/4 mile/7.640 sec. 178.57mph
Following in the slick marks left by Don
Garlits' Swamp Rat, HEMI® engines were a common choice for the supercharged,
lightweight dragsters that ran in the AA/fuel class, burning
nitromethane/alcohol mixtures. The rugged design of the HEMI® could withstand
even the 1,200 to 1,500 hp generated by the cars. This dragster built in 1967
used a 1957 392 c.i.d. HEMI® as the starting point. It is equipped with Hilborn
fuel injection and a Roots-type 8-71 supercharger. A Hayes sliding clutch
couples the drive shaft directly to the solid rear axle. There is no
transmission. Wheels are 16-inch, polished American mags with M & H racing
slicks. Dubbed "Probe," this car competed in the Midwest between 1967-1969 for
the Phil Goulet (tuning) and Ray DeNoble (driver) team.
Logghe Stamping Company of Warren, Mich.,
fabricated Probe's frame of chrome-molybdenum tubing; the aluminium body was
fabricated by Al Bergler.
Minimum Ground Clearance: 3"
The Silver Bullet drag car is powered by a 426 HEMI® bored
and stroked to 487 c.i.d. with other modifications that permit quarter-mile
times in the mid-10-second range with top speed close to 140 mph.
The saga of the "Silver Bullet" began with Jimmy
Addison, the manager of a Sunoco station on Woodward Avenue, and a man known for
his skill in setting up a car for drag racing competition. He was also famed as
a street racer, driving a 1962 Max Wedge Dodge. Addison was respected by
Chrysler performance engineers, who helped him acquire a 1967 Plymouth Belvedere
GTX used to set 440 four-bbl Wedge component combinations.
Connections at Chrysler also helped Addison build
a bored and stroked HEMI® with aluminium heads, special cam, carburettors and
pistons to replace the Wedge. The HEMI® was matched with a Torqueflight
automatic transmission fitted with a 4,000 rpm stall converter, special rear end
ratios and 12-inch slicks on the rear tyres. Addison installed fibreglass
fenders, doors, hood and decklid to drop the overall weight by some 500 pounds.
Flared rear fenders were necessary due to the wide slicks, and the car was
painted silver. When journalist Ro McGonegal wrote about the car for the
September 1971 issue of Car Craft magazine, he supplied the name - the "Silver
Retired from racing, the "Silver Bullet" was found
and restored by noted Mopar muscle car collector Harold
A journey through a remarkable engine's remarkable
1939 Chrysler begins design work on first HEMI®, a
V-16 for fighter aircraft.
1951 Chrysler stuns automotive world with 180 hp
HEMI® V-8 engine.
1951 Chrysler New Yorker convertible paces Indianapolis 500
1951 Saratoga first in Stock Car Class; second overall in Carrera
Pan-Americana road race.
1951 Briggs Cunningham chooses HEMI® engines for his
Le Mans race cars.
1952 A special HEMI® is tested in a Kurtis Kraft
Indy roadster; it's banned by racing officials as too fast.
1953 Lee Petty's HEMI® Dodge wins five NASCAR
races and finishes second in championship points.
1953 Cunningham's C-4R
HEMI® wins 12 Hours of Sebring and finishes third at Le Mans.
1953 A Dodge
HEMI® V-8 breaks 196 stock car records at Bonneville Salt Flats.
1954 A Chrysler HEMI® with 4-barrel and dual
exhausts makes 235 hp.
1954 Lee Petty wins Daytona Beach race in a Chrysler
1954 Lee Petty wins NASCAR Grand National championship driving Chrysler
and Dodge HEMI®s.
1954 Cunningham HEMI®s win Sebring again, third and fifth
at Le Mans.
1954 Dodge Red Ram HEMI® convertible paces Indy 500.
1955 Chrysler introduces the legendary 300 as
America's most powerful stock car
1955 Chrysler "300" with dual 4-barrel 331
c.i.d. HEMI® is first production car to make 300 hp.
1955 A Carl
Keikhaefer-prepared Chrysler 300 wins at Daytona Beach with Tim Flock
1955 Chrysler bumps HEMI® to 250 hp in New Yorker and 280 hp in
1955 Frank Mundy wins AAA Championship in Kiekhaefer-prepared
1956 DeSoto Fireflite HEMI® convertible paces
1956 Chrysler 300-B HEMI® increased to 354 c.i.d. and 340
hp with dual 4-barrels.
1956 Buck Baker wins NASCAR Grand National
Championship in Chrysler 300-B with 14 wins.
1956 Chrysler 300-B sets World
Passenger Car speed record at Daytona Beach - 133.9 mph.
1956 Don "Big Daddy"
Garlits begins 46-year winning association with Chrysler HEMI®s.
1957 Chrysler 300-C HEMI® increased to 392 c.i.d.
and 375 hp.
1958 Last year of HEMI® engine in Chrysler 300
1958 Don "Big Daddy" Garlits breaks the 170 mph barrier in his "Swamp
Rat" HEMI® dragster.
1958 Chrysler 300-D HEMI® sets a Class E speed record at
Bonneville at 156.387 mph.
1959 Original Ramchargers debut "High &
Mighty" HEMI®-powered C/A (altered class) '49 Plymouth to win NHRA
1964 A.J. Foyt wins Firecracker 400 at Daytona;
Plymouths or Dodges lead every lap.
1964 Chrysler introduces the 426 c.i.d.
race HEMI® into competition.
1964 Richard Petty debuts the 426 HEMI® and laps
the field while winning the Daytona 500.
1964 Three HEMI® -powered Plymouths
and a HEMI® Dodge sweep Daytona 1-2-3.
1964 HEMI®-powered stock cars win 26
of the 62 NASCAR Grand National races.
1964 Richard Petty captures his first
of seven driving championships with eight wins, 37 top-five finishes.
Don Garlits breaks 200 mph quarter mile barrier in HEMI® dragster - 201.34 mph
in 7.78 sec.
1964 Jim Thornton wins 1964 U.S. Nationals in Ramcharger's
"Candymatic" 426 HEMI® Dodge.
1964 Jim Paschal wins NASCAR World 600 at
Charlotte Motor Speedway in HEMI®-powered Plymouth.
1965 NASCAR outlaws HEMI® by setting minimum
production levels for street use.
1965 Bob Summers sets present 409.227 mph
Land Speed Record in "Goldenrod" using 4 HEMI®s in tandem.
Shahan becomes first female to win major NHRA event driving a HEMI®
1966 Chrysler builds the "Street HEMI®" and
returns to NASCAR racing.
1966 Richard Petty again wins Daytona 500 in his
HEMI® Plymouth Belvedere.
1966 HEMI® Dodge Charger wins the NASCAR
Championship, Plymouth is second.
1966 Norm Nelson wins USAC stock car
championship with seven wins in a HEMI® Plymouth.
1967 Richard Petty wins an incredible 27 Grand
National races in HEMI® Plymouth; 10 in a row.
1967 Richard Petty wins his
second NASCAR championship in his HEMI® Plymouth.
1967 Don White's Charger
gives HEMI ® cars second USAC championship in a row.
1968 Sox and Martin win three major AHRA events;
Ronnie Sox named AHRA Driver of the Year.
1968 Dodge and Plymouth produce a
limited number of 426 HEMI® Super Stock Darts and Barracudas.
Runner, first budget muscle car, is introduced by Plymouth; available with 426
1969 Dodge introduces Charger 500 HEMI®, which
wins 22 NASCAR races.
1969 The "winged" 1969 Dodge Charger Daytona with HEMI®
power reigns over NASCAR superspeedways.
1970 Buddy Baker is the first to break 200 mph on
a closed course in a HEMI® Dodge Charger Daytona stock car.
1970 Bobby Isaac
sets a closed course speed record - 201.104 mph - in a Dodge Charger Daytona
after winning the NASCAR championship.
1970 Sox and Martin HEMI® Plymouths
win 17 major championships and are runners-up in all other major events.
Bobby Isaac breaks 28 records at Bonneville in a Dodge Charger Daytona; top
speed is 217.368 mph.
1971 Richard Petty wins his 3rd NASCAR Grand National
championship in a HEMI® Road Runner.
1971 Don Garlits introduces HEMI-powered
rear engine dragster at NHRA Winter Nationals.
1971 Sox and Martin win six of
eight NHRA events; they represent drag racing at a presidential
1991 Al Teague sets 409.986 mph wheel-driven Land
Speed Record in the Supercharged class with single HEMI®.
2003 5.7-liter HEMI® "Magnum" develops up to 345
hp and 375 lb.-ft. of torque.
2003 5.7-liter HEMI® "Magnum" in Ram 2500/3500
series trucks delivers best-in-class power, acceleration and towing
2003 5.7-liter HEMI® "Magnum" is 56 lbs. lighter, has 41% more
power and 12% more torque than the 5.9-liter Magnum wedge head engine it
2003 5.7-liter HEMI® is the first Chrysler production gasoline
engine with electronic throttle control or "Drive-by-Wire".
5.7-liter HEMI® meets all federal emissions standards, delivers 8-10% better
economy than the engine it replaces.
2003 5.7-liter HEMI® "Magnum" is the
first Chrysler production engine to use two spark plugs per cylinder.
2003 5.7-liter HEMI® features "Leak Free" design
with a cast-in drain through on the oil filter pad.
2003 HEMI® architecture
produces power comparable to an overhead cam engine, yet is less costly to