Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Using Relays

There're just electrical switches - but bloody useful ones!

by Julian Edgar

Click on pics to view larger images

At a glance...

  • Function
  • Pin codes
  • Internal designs
  • Sample circuits
  • Example uses
Email a friend     Print article
This article was first published in 2005.

In any electrical system, relays are amongst the most useful of components. They let you control heavy loads with light-weight switches, allow one device to be switched off at the same time as another is switched on, are very hard to blow-up, and are cheap and widely available. That’s a damn good list of attributes!

So how do you use them?

What’s a Relay?

Click for larger image

A relay is just a small switch whose movement is caused by the action of an electromagnet inside. When power is applied to the relay’s coil, the electromagnet comes alive and pulls across the switching contacts.

Relay Types

  • Single Pole, Single Throw

The simplest relay is a single pole, single throw (SPST) design. This designation refers to the switching part of the relay where when it's activated, one wire (a "single pole") can be connected only one way (a "single throw"). Just like an on/off switch, when you power up the relay's coil, the connection is made; when you unpower the coil, the connection is broken.

Click for larger image

In this diagram the relay's coil is yellow. Near to the coil you can see a switch, which is open. This is called a Normally Open contact - it's open when there's no power being applied to the relay. When power is applied to the relay’s coil, the single contact closes. This is a Single Pole Single Throw relay - SPST. SPST relays have four terminals - two are to power the coil and the other two are the connections for the internal switch. As you can see, there is no electrical connection between the pair of contacts for the coil and the pair of contacts for the switching side of the relay.

Click for larger image

On automotive SPST relays, the pins are given standardised numbers. The coil connections are 85 and 86, while the two connections for the internal switch are 30 and 87. However, most general purpose relays don’t have any numbers on the pins – instead the functions of the pins are shown on a little diagram on the body of the relay.

The most common use for a SPST relay is to use a small electrical current to control a large electrical current. For example, a radiator fan might be triggered by a temperature switch. The temp switch is capable of flowing only 2 amps, but the radiator fan at switch-on takes 15 amps (and then settles back to 8 amps continuous).

Click for larger image

If you wire the radiator fan to the switch like this, after a few weeks the switch would fail – its contacts are being hugely overloaded.

Click for larger image

The solution is to add a SPST relay that is wired into the circuit like this. Neither the relay coil nor the switching part of the relay have polarities – both can be connected either way around to 12V and Ground. As we said earlier, a relay is very hard to blow-up!

  • Single Pole, Double Throw

Click for larger image

But wouldn't it be good if we had a contact that was broken at the same time as the switch was made? That's what happens in the Single Pole, Double Throw design. Another contact has been added that is Normally Closed. When the relay is energised, this contact is broken and the other one (the Normally Open contact) is closed. We still have only a single pole to be switched, but now it can be connected two ways - a double throw design. This type of relay is therefore called a Single Pole, Double Throw relay. As you can see, it has both Normally Open (NO) and Normally Closed (NC) contacts. Some people call this a changeover relay.

Click for larger image

A SPDT relay allows you to control two devices, switching one off as the other is switched on. A recent example of where I needed to use a relay in this way is in a fuel system that needed to be switched between two different fuel pressures. To raise the fuel pressure, a solenoid valve had to be turned off and at the same time, a fuel pump needed to be switched on. Both devices draw a fair amount of current so a heavy duty automotive relay was used.

SPDT automotive relays use the following codes for their pins: the coil connections are again 85 and 86, the normally closed output is 87a, the normally open output is 87 and the input is 30.

Click for larger image

The circuit diagram for the fuel system relay looks like this. Power is normally supplied to the solenoid through the Normally Closed (NC) relay contact, energising the solenoid. But when the relay’s coil is activated (by closing the High/Low Fuel Pressure switch), the relay pulls the contact across, switching off the solenoid and switching on the fuel pump. The High/Low Fuel Pressure switch has to handle only enough current to switch the relay’s coil, so this can be a light-duty switch (eg a boost pressure switch or a microswitch).

  • Double Pole, Double Throw

Click for larger image

A Double Pole, Double Throw relay allows you to switch two different circuits simultaneously. The 'Double Pole' bit just means that it has two separate inputs that can be switched - and we now know what the 'double throw' stuff means. With this type of relay you can:

- turn on two completely independent circuits

- turn one off and one on

- turn off two completely independent circuits

These relays are less common in automotive aftermarket use and so don’t have coded numbers for the pins.

So what use is a DPDT relay, then? Again, I’ll use an example from a recent car modification I have been working on. What was needed was the on-demand disconnection of two oxygen sensor input signals to the ECU. The two signal wires from the oxy sensors to the ECU needed to be kept completely separate, so they couldn’t be joined together and a SPST relay used. Instead a DPDT relay was used. (It didn’t actually have to be a double throw design, but DPDT relays are more common than SPDT designs.)

Using a Relay

Click for larger image

Using a relay is made a lot simpler if you follow these steps.

Draw a circuit diagram. The first step is to draw a simple circuit diagram showing where the wires go. Which wires go to the relay coil, which to the Normally Open and Normally Closed contacts of the relay?

Decide what type of relay is needed. If just one connection needs to be switched on and off, you’ll use a SPST design. If two connections need to be switched, a DPST or (more commonly) a DPDT design will be the one to use. A changeover (where one device is switched off and the other switched on) can use a SPDT or a DPDT design.

Work out the functions of each pin. If it’s a standard automotive relay, read the numbers. If it’s a general purpose relay, look for the diagram on the relay body. If neither of these apply, by careful use of a short-circuit protected power supply and a multimeter, you can work out the functions of each pin. (Unless you use too high a test voltage, you can’t damage the relay!)

Wire the relay coil first. If you wire the relay’s coil first, you’ll be able to check that the relay is working by listening to its click.

How Complex?

Click for larger image

It’s easy to think of relays as being suitable for just simple car modifications, but that’s not always the case.

This circuit shows the use of two relays that deactivate traction control without affecting ABS or stability control. The system works by connecting the un-driven wheel ABS sensor outputs to the driven wheel ECU inputs, so that the ECU cannot see a speed difference between the undriven and driven wheels. The modification is automatically switched off whenever the brakes are applied, or by a manual on/off switch. This diagram shows only half of the system - the complete the system just mirror-images the wiring for the other side of the car.

The total cost of the modification was well under AUD$30 – relays are cheap! For more on this approach, see Modifying Electronic Car Handling Systems, Part 3

Relay Specifications

In addition to its contact configuration (SPST, DPDT, etc) there are at least three other specifications that are important.

  • Coil voltage

This refers to the voltage which the relay is designed to have its coil triggered by. A nominally 12V relay is fine on car voltages, even though they can extend as high as 13.8V. However, you shouldn’t use a 5V coil relay on a 12V system. (But note that a 24V relay, if it’s a sensitive design, will often work fine on 12V!)

  • Coil current

This is the amount of current the relay coil will draw when energised. This can be expressed directly in milliamps, or indirectly as a coil resistance. A very sensitive relay might have a coil resistance of 360 ohms. 13.8 volts divided by 360 ohms gives a coil current of 0.038 amps, or 38 milliamps. In other words, the switch that you’re using to operate the relay has to handle just 38 milliamps. But this is a very low value of required current. A typical automotive relay is more likely to have a coil resistance of 80 ohms, giving a coil current flow of 170 milliamps. (13.8/80 = 0.17 amps)

  • Maximum Contact Current

Click for larger image

This spec refers to the max current that a relay’s contacts can handle. To avoid arcing, you should use a factor of safety where the max current of your switched circuit (even when it first switches on with a current gulp) is less than the relay’s spec. Automotive relays are available with current ratings like 25, 30 and even 60 amps. Be careful when checking max current specs that the listing is for the DC at or above the voltage you’ll be using – ie, in cars, 13.8V. For example, a relay rated at 10 amps at 240V AC is not the same as one rated at 10 amps at 12V DC.

Other specs that you might fine listed include life (ie how many millions of operations the relay will do before failure) and perhaps response time.

Conclusion

Click for larger image

Relays can be useful in nearly every electrical or electronic car modification. Get your head around their use and you’ll never regret having spent the time to find out how they can be used.

A Relay-based Immobiliser

Once you’ve got familiar with relays, you might want to try out this – a relay-based immobiliser. It works very well and is very hard for a thief to bypass – see The World's Best DIY Immobiliser

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Less than 1 litre/100km fuel economy from this stunning concept vehicle

Special Features - 3 May, 2011

Volkswagen's Eco-Stunner

Why if you're interested in economy or power, you must know about water injection

Technical Features - 15 April, 2008

The H2O Way, Part 1

Fuel economy of 1 litre/100km from an amazing car

Technical Features - 11 June, 2002

The World's Most Fuel-Efficient Car

Stopping vibration in its tracks

DIY Tech Features - 15 December, 2009

Designing Rubber Mounts

Setting up oxy acetylene gear

DIY Tech Features - 29 June, 2007

Beginners' Guide to Welding, Part 2

So what makes a vehicle have a good ride?

Technical Features - 4 May, 2010

Ride Quality, Part 1

One of the most extraordinary racing cars ever built

Special Features - 29 July, 2014

The Mercedes Benz W196

Debunking untruths

Special Features - 1 September, 2009

Automotive Myths

A different electric fan

DIY Tech Features - 9 June, 2009

Chasing Overheating - Again!

Then the world's most powerful six cylinder passenger car diesel

Technical Features - 6 June, 2005

BMW's Twin Turbo Diesel

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip