Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Force Fed Ferrari

A Ferrari F355 Spyder that runs easy 10 second quarters thanks to a custom twin-turbo set-up!

Words by Michael Knowling, Pix by Julian Edgar

Click on pics to view larger images

At a glance...

  • 1996 Ferrari F355 Spyder
  • Twin-turbo and intercooler installation
  • MoTeC M800
  • 10 second quarter mile
  • Top speed well in excess of 320 km/h
Email a friend     Print article
This article was first published in 2005.

Ferraris have a reputation for speed. Pure, simple speed. But when Tony X pulls alongside you’d better be prepared to witness something totally dumbfounding. The speed of this prancing horse will challenge your grasp of physics!

You’re looking at a regularly street driven Ferrari that punches out 450kW at the back wheels and can howl down the quarter mile in 10.9 seconds - on street tyres!           

Step aside McLaren F1!

Tony is no stranger to performance. He’s owned a Ferrari 348 Spider, various Porsches (including a low 11 second 944 Turbo) and he also owns a drag racer - a Camaro Top Door Slammer. His F355 Spider was purchased brand new back in 1996 and was the second to arrive in the country (it was originally flown in for the 1996 Brisbane Motor Show).

Click for larger image

The F355 is powered by a 283kW (380hp) 3.5 litre V8 running 5-valve-per-cylinder heads, individual throttle bodies and lightweight titanium rods. It’s also one of the first models to bring full under-car aerodynamics into production. Tony says the F355 was a great machine back in the late ‘90s but he soon grew blasé about its standard performance. This was made worse by the fact that emerging performance cars (such as HSV LS1s) were offering performance scarily close to the mighty Ferrari.

Time to fix that situation!

Click for larger image

Tony says he investigated turbo and supercharger kits from all over the world but the high cost - and the fact that the car would need to be shipped overseas - were major turn-offs. It was local tuning workshop – Nizpro - that got the job of breathing boost into the Italian Stallion.

Turbocharging a Ferrari was a project that Simon of Nizpro grabbed with both hands. We’re told that the conversion was pretty straight-forward - the only out-of-the-ordinary step was the requirement to fabricate a custom muffler to suit the available space.

Simon’s initial assessment of the project was “it’ll be a piece of piss.”

Click for larger image

The 11.5:1 compression ratio engine was to remain intact which means mild boost pressure and careful engine mapping were essential. Simon used a pair of modified HKS 25/30 turbochargers that are mounted on custom manifolds. He chose to mount the turbochargers at the rear of the engine compartment about one metre away from the exhaust ports. This seems less than ideal from a turbo lag point of view but we’re assured the engine is very responsive. The exhaust manifolds use 1 ½ inch primaries leading into 1 3/4 inch pipes to the turbos. A single Turbosmart 48mm external wastegate is also integrated into the new manifold arrangement. An oil feed for the turbos was inserted into a distribution block that branches out to the factory oil cooler.

Due to limited space beneath the turbos, Nizpro fabricated a custom muffler which comprises inlets in the centre topside of the muffler body and outlets at each end on the bottom. It’s a straight-through design to give maximum gas flow.

Click for larger image

Induction air is filtered by a pair of K&N filters mounted on the turbo compressor mouths while boosted air is flung through a pair of custom side-mount intercoolers. These intercoolers are fed cooling air from the F355’s side intakes while electric fans draw air through the cores to maintain cool charge-temps in traffic. Twin Bosch blow-off valves (ex Ford XR6 Turbo) route air back to the compressor inlets on gear changes.

Click for larger image

Fuel delivery is provided by 60lb Siemens injectors, a stock Ferrari regulator and a Bosch Motorsport fuel pump. The upgraded injectors and pump are required to maintain a 12.8:1 air-fuel ratio at the engine’s current power output. Fuel and (standard) ignition are controlled by a top-line MoTeC M800 ECU. The M800 is also used to activate the intercooler fans above a preset intake air temperature and limits engine speed to 9500 rpm. It seems that the engine will happily keep making power beyond 10,000 rpm - but nobody wants to pick up the pieces when the mechanical limits are found...

Click for larger image

With boost pressure set to 14 psi and tuned to run pump 98 RON fuel, the F355 TT has spat out 450kW at the wheels on Nizpro’s DynoLog chassis dyno. The top section of this dyno printout shows the power curve while the lower section shows the boost curve. As you can see, full boost is achieve at just over 5000 rpm and holds steady to beyond 8000 rpm. With the rev limit set to 9500 rpm there’s a healthy 4500 rpm operating range under full boost.

Click for larger image

Despite the monumental increase in torque, Tony uses an original Ferrari clutch – it has done 8000km of service with the turbos (83,000km in total) and shows no sign of dying. Tony says retaining the original clutch puts less strain on the 6-speed manual gearbox - he’d much rather fit a new clutch than a new Ferrari ‘box...

Grip is enhanced with huge 295/35 Pirelli Corsa semi-track tyres fitted at the rear while the standard 225/40 Pirelli P-Zeros are used at the front. Tony says the previous Pirellis (which were three years old) were getting fried with the turbo grunt but, still, they helped him along to a best quarter mile time of 10.92 seconds at 132 mph. We’re told that the new Corsa tyres should improve times considerably.

Click for larger image

Tony isn’t big on circuit racing but he has upgraded the brakes to 355mm drilled disc and 4-pot Brembo caliper kit from overseas. A powerful set of anchors is essential with the speed this horse can run to.

And how much speed are we talking?

Click for larger image

Well, Simon has driven this twin-turbo beast off the clock - in Simon’s words, “the speedo needle was touching the horse’s arse...” And that, readers, is well beyond 320 km/h! It’s no wonder Tony has annihilated a Suzuki Hayabusa from a 100 km/h rolling start. Tony also points out that the car is deceptively fast and stable - at 280 km/h it feels like 170 km/h.

Except for the glorious engine noise...

Simon says the Ferrari engine is very well suited to forced induction. It doesn’t need a lot of ignition timing retard on boost (which is indicative of a very efficient combustion chamber) and no previously hidden weaknesses have been found. In fact, Simon is so happy with the final product he’s now offering a Ferrari twin-turbo kit using all the same parts as Tony’s car. Total cost for the kit is around AUD$40,000 depending on your required power output.

Click for larger image

For now, Tony is more than happy to leave the car pretty well as is. However, he does plan to retune the engine for race fuel and bump up the boost for another quarter mile attack. He’d like to fit some bigger rear tyres but, unfortunately, the rear wheel arches don’t leave much extra space.

“Simon feels there’s 800hp (600kW) waiting there and it’d be nice to see if we can take it a bit faster,” says Tony.

Any chance this will become the world’s first Ferrari Door Slammer?!

Contact:

Nizpro                                                   +61 3 9761 1522

                                                            www.nizpro.com.au

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
An extraordinary engine that was light, powerful and fuel-efficient

Special Features - 5 March, 2013

Napier Nomad

A brilliant new temperature controller that's so cheap it's unbelievable.

DIY Tech Features - 15 November, 2011

$25 Temperature Controller and Display!

Riding a DIY electric bike

DIY Tech Features - 18 February, 2005

Building an Electric Bike Part 3

How they built the fastest diesel on Earth

Special Features - 30 January, 2007

350.092 mph - Breaking the Diesel Speed Record

Peak boost in one-third of a second!

Technical Features - 5 October, 2010

Is This Your Electric Supercharger?

Dressing MIG welds made in car bodywork

DIY Tech Features - 3 June, 2014

Dressing MIG Welds

Evaluating the finished home workshop

DIY Tech Features - 14 October, 2008

Building a Home Workshop, Part 10

Ten great home workshop ideas

DIY Tech Features - 16 May, 2008

Useful Ideas

Stopping the heat spreading

DIY Tech Features - 1 July, 2014

Making turbo heat shields

Building a programmable temperature alarm

DIY Tech Features - 13 October, 2009

eLabtronics EZ System, Part 2

Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip