Magazines:  Real Estate Shopping: Adult Costumes  |  Kids Costumes  |   |  Guitars |  
This Issue Archived Articles Blog About Us Contact Us

Thermo Fan Install

Step-by-step fitment of a thermo fan.

By Michael Knowling

Click on pics to view larger images

Does your car run a bit warm? Well, here's how to fit a thermo fan...

Buying and Mounting

Click for larger image
Second-hand thermo fans can be bought cheaply at your local wreckers. This example was pulled from an early '80s Mercedes and cost just AUD$22. It measures 12 inches in diameter and is very slim, making it ideal for our particular application.

Buying Tips

It's a good idea to look for a thermo fan from a vehicle that's the same make as yours - there might be mounting similarities to make the installation easier.

Click for larger image
Also - where possible - grab the wiring all the way up to the loom connector. Snip the wires on the loom side of the connector so you've got a nice, factory-style connector to be used as part of your installation. Shown here are the male and female connectors for the Mercedes thermo fan.

The thermo fan can be mounted using brackets fabricated from aluminium strips. Note that the brackets should be quite sturdy and not thinner than about 2.5mm.

Click for larger image
As seen here, 2.5mm thick aluminium strip can easily be bent to the appropriate shape using a vice and a pair of multi-grips. You can use a piece of cloth between the jaws of the grips if you want to avoid marking the soft aluminium surface.

Click for larger image
Our installation required only two brackets to secure the fan - and here are the finished products. About an hour of effort was all they took.

Firing Up the Fan

Click for larger image
Due to the high current draw of a thermo fan you'll need to run its 12-volt power supply through a relay. You'll also need a method of switching the fan on and off at certain coolant temperatures and, of course, only when the ignition is on. There are a number of ways to achieve this, but one of the easiest is to buy a Davies Craig Thermal Switch kit. These kits retail for around AUD$80 and include the necessary relay, an adjustable temperature switch, mounting bracket and a complete wiring loom including terminals and a fuse holder.

Note that this kit dates back a few years so you might be lucky enough to find a second-hand one at the wreckers when you're looking for the thermo fan.

Click for larger image
The first step is to mount the kit's temperature sensor inside the top radiator hose. The copper sensor can be slipped beneath the radiator hose using a grooved rubber seal to prevent any leaks. The radiator hose clamp is simply retightened over the top as per usual.

The sensor's copper tail is connected to the adjustable temperature switching mechanism, which should be mounted on a (supplied) bracket near the radiator.

Click for larger image
Next, find a position to mount the thermo fan relay. Somewhere between the battery and radiator is ideal. There are four wiring connections to the relay - a 12-volt supply, earth, a switched input and the positive power output to the fan.

Click for larger image
The relay's 12-volt supply can come straight off the battery but make sure the supplied fuse holder is mounted close to the positive post to ensure maximum safety. The relay's earth can be either the battery's negative post or a reliable body earthing point. Note that the earth lead from the thermo fan can share the same earthing point as the relay - this makes installation easy.

Wiring the thermo fan's switched input requires a bit more effort. Find an existing wire under the dash that is switched on and off by the ignition (such as the switched power supply to the radio) and use the supplied scotchblock terminal to T in another wire.

Click for larger image
This new wire should then be connected to one of the terminals of the adjustable temperature switch mechanism. The second terminal of the switch mechanism should then be wired to the relay. (Note that the pins of the relay are clearly identified in the Davies Craig installation instructions) This arrangement means the fan will activate only when the ignition is on and the coolant temperature switch has been tripped.

The last step of the installation is to insert the appropriate spade fuse into the fuse holder. In the case of a 12-inch thermo fan (such as ours) you'll generally need a 20-amp fuse, while less powerful fans use smaller fuses.

Click for larger image
Start the car, go for a drive and watch that temp needle stay below the danger zone. Congratulations - job done!

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...

Share this Article: 

More of our most popular articles.
A unique solution to reducing vibration in driving lights

DIY Tech Features - 16 October, 2012

Mounting big driving lights, Part 2

Turbine cars promised so much - but they're not the answer

Technical Features - 27 September, 2007

Alternative Cars, Part 3 - Turbine

Ten great home workshop ideas

DIY Tech Features - 16 May, 2008

Useful Ideas

Building an adjustable temperature alarm - and more!

DIY Tech Features - 27 October, 2009

eLabtronics EZ System, Part 4

DIY knock detection - cheap, easy and very effective!

DIY Tech Features - 18 November, 2014

Hearing Detonation

A revolutionary fuel saving device that works

Columns - 25 August, 2009

FuelSmart, Part 2

Dressing MIG welds made in car bodywork

DIY Tech Features - 3 June, 2014

Dressing MIG Welds

Do-it-yourself aero testing of a Porsche and new Beetle

Technical Features - 27 June, 2007

Aero Testing, Part 3

Setting up oxy acetylene gear

DIY Tech Features - 29 June, 2007

Beginners' Guide to Welding, Part 2

Mixing a dose of LPG with diesel to improve power and economy

Technical Features - 12 March, 2008

Diesel LPG - an Amazing Breakthrough

Copyright © 1996-2019 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip