Magazines:  Real Estate Shopping: Adult Costumes  |  Kids Costumes  |  Car Books  |  Guitars |  Electronics
This Issue Archived Articles Blog About Us Contact Us
SEARCH


Dressing MIG Welds

Dressing MIG welds made in car bodywork

Courtesy I-CAR

Click on pics to view larger images


This article first appeared in the I-CAR Advantage Online, which is published and distributed free of charge. I-CAR, the Inter-Industry Conference on Auto Collision Repair, is a not-for-profit international training organization that researches and develops quality technical education programs related to collision repair. To learn more about I-CAR, and to subscribe to the free publication, visit http://www.i-car.com

There’s a lot of information in the field on making and testing GMA (MIG) welds, but not too much on dressing the welds after they’re made on a vehicle. Any GMA (MIG) usually requires dressing the top surface of the weld.

Does Dressing Reduce Strength?

Click for larger image

There is a belief by some, that dressing a weld reduces the strength of that weld. If you look at a cross-section of an undressed plug weld, it looks similar to the shape of a blind rivet, with the crown of the weld the head of the rivet. Once the weld is dressed, it would be like grinding off the head of the rivet. Is the joint as strong? With a rivet, the answer is no, but then again a rivet is not fused to the metal around it.

Click for larger image

A good plug weld is fused to the metal around it.

We made several plug welds on identical size strips so we could pull them on our tensile testing equipment, some dressed flush and some undressed.

In general, there was an insignificant difference in tensile strength between those that were undressed and those that were dressed flush. Some of the dressed welds started failing on the top piece, rather than starting to pull a nugget out of the base metal. These welds had porosity or some other inclusion that was revealed after dressing and we don’t believe the dressing to be a factor.

The Process

So how far do you dress a weld? The short answer is so that it is flush with the surface. It’s important to not reduce the thickness of the base metal, because that will weaken the structure. The only way to prevent that is to use light pressure and check your progress often.

Click for larger image

As far as tool selection, a common initial tool to use is an angle grinder, with a 36 or 50 grit disc depending on the size of the bead or nugget.

The disc is lightly applied to the weld and moved slowly back and forth. If there are multiple welds, like a row of plug welds, they are ground one at a time.

On a butt joint, again use a light touch and slow movement. It doesn’t matter if you move the grinder across the weld or lengthwise down the weld, whatever works best for you. The important part is always being conscious and careful to not grind into the base metal.

Click for larger image

Another tool that can be used is a cutoff wheel, but this tool is not as precise a tool as an angle grinder. There’s a temptation to use this tool exclusively because it’s aggressive, as in fast, but it’s difficult to control, especially when you get close to the base metal. If used at all, it should only be the first step, then followed with an angle grinder.

When using a cutoff wheel, just like the angle grinder use light pressure. Hold the tool with two hands for better control. Start at a high RPM and walk the edge slowly across the surface of the weld, like you’re planing off the surface of the bead. Stop when there is still a slight profile left on the weld. Do not touch the base metal surrounding the weld at all. This should keep you out of trouble. Again, follow this up with an angle grinder to get flush with the base metal.

Click for larger image

Still another tool that can be used is a carbide rotary file. There are a couple different profiles available. This is used when the plug weld is in a recess or access won’t allow access for a disc. This tool is difficult to control, so use extreme caution or you could damage an adjacent area.

You can finish the dressing with a hand file, maybe progressing through a couple different grades until the surface is flush as it needs to be.

Conclusion

Nearly all GMA (MIG) welds require dressing. The goal of dressing GMA (MIG) welds is to make the surface flush. Gouging below the surface of the base metal not only looks bad, it weakens the steel. Keep this in mind whenever doing this process.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Tuning the system

DIY Tech Features - 8 January, 2013

Sound in the Lounge, Part 4

The first steam turbine powered vessel - and it was the fastest in the world!

Special Features - 27 July, 2010

The Turbinia

Under $10 for a remote-controlled immobiliser!

DIY Tech Features - 27 November, 2012

DIY classic car immobiliser

Putting a super-bright LED interior light in your car

DIY Tech Features - 21 July, 2008

Upgrading to LED Interior Lighting

The world's brightest flashing bike tail-lights?

DIY Tech Features - 18 February, 2008

Building a High Performance LED Lighting System, Part 2

Ten great home workshop ideas

DIY Tech Features - 16 May, 2008

Useful Ideas

How they built the fastest diesel on Earth

Special Features - 30 January, 2007

350.092 mph - Breaking the Diesel Speed Record

So what makes a vehicle have a good ride?

Technical Features - 4 May, 2010

Ride Quality, Part 1

What's happened to electronic advances in cars?

Special Features - 19 May, 2009

Car Electronics Going Nowhere?

A new engine designed to extend the range of plug-in hybrid cars

Special Features - 8 December, 2009

The Lotus Range Extender Engine

Copyright © 1996-2017 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip