Magazines:  Real Estate Shopping: Adult Costumes  |  Kids Costumes  |  Car Books  |  Guitars |  Electronics
This Issue Archived Articles Blog About Us Contact Us
SEARCH


High Performance Gearbox Steels

Achieving seven times the life from ultra-high performance gearboxes!

Courtesy of Xtrac

Click on pics to view larger images


This article was first published in 2010.

Click for larger image

This article is based on a presentation to the Aerospace Industries Division of the UK’s Institution of Mechanical Engineers by Xtrac’s chief metallurgist, Steve Vanes. It is used here with permission.

Motorsport, and in particular Formula One, has always made use of new technology. In the early part of this decade the emphasis was on reducing weight and increasing performance, requiring the transmission of greater power through thinner or smaller components. At that time, the typical life of a gearbox mainshaft gear may only have been ~350 thousand cycles.

In recent years, however, the technical regulations have gone through major changes, with many aimed at lowering the cost of racing. Achieving extended life (and so lower costs) has meant the standardisation of gearbox design, and introducing minimum face width and weight requirements for gear ratios.

Click for larger image

For 2008/9, transmission components were required to achieve a four-race life, which was quite a considerable jump in terms of life expectancy from earlier in the decade. For the future (2011 onwards) the requirement is likely to be extended still further to six races, which will equate to a life of more than 2.5 million cycles.

This article aims to review some of the developments in gear steels introduced into Formula One and sports car transmissions over the last decade, and others which are anticipated to be adopted in the future.

Development of Motorsport Steels

From the early 1990s the primary gear steel used in motorsport applications was EN36C (832M31), and designs and heat treatment followed those typically applied to aerospace components.

Click for larger image

Towards the end of the 90’s, the focus in Formula One transmissions was centred largely on increasing power and reducing weight. It was the effect of these running conditions that caused bending fatigue to become the over-riding material limiting factor. Typical failures resulted from the initiation of fatigue cracks in the fillet radius of gear tooth roots, often leading to the loss of one or a number of gear teeth, as shown here. The focus of activity was therefore on how to increase bending fatigue resistance.

As well as the steel alloy’s chemistry being a performance variable, so also is the heat treatment. Virtually all transmission components are case hardened (by carburising), so this in turn offers a number of other variables such as case depth and surface hardness.

To be able to quantify the effects that material and heat treatment (and their interrelationship) have, a means of evaluating properties was required.

Tensile test data, although used extensively in the past for design, was considered of little practical importance when trying to predict and evaluate component life and performance. Consequently, at Xtrac the basic evaluation tool that has been used is a cantilever bend test, which allowed the elastic and plastic properties of a material and its heat treatment to be evaluated.

Click for larger image

Initially, we established baseline performance for mechanical properties and how these may be influenced by case hardening depth, surface and core hardness. This included characteristics of yield strength, fracture strength and strain hardening.

Click for larger image

From these evaluations it was possible to ascertain how alloy type and heat treatment affected mechanical properties. Once promising configurations had been identified, a four square rig test was used to evaluate the bending fatigue, rolling contact fatigue and performance of lubricated test gear components subjected to environments similar to those experienced in service.

Gear Steels – Old and New

Over the last 100 years, engineering steels have been extensively developed and researched, creating a wide and varied range of specifications. However a relative few have found favour in motorsport applications and a list of the most notable is shown below.

Material Type

Description

Applications

Comments

En36C (VAR)

14NiCrMo13

3%NiCrMo case hardening

steel

Gear, shaft and bearings

Low core strength (UTS:1350MPa)

Low tempering temperature 140/160 degrees C

S156 (VAR)

16NiCrMo17

4¼%NiCrMo case hardening steel

Gear and bearings

Low core strength (UTS:1380MPa)

Low tempering temperature 160/180 degrees C

20NiCrMo13 (VAR)

3%NiCrMo case hardening

steel (increased core strength)

Gears and shafts

Higher core strength achieved by increased core carbon content.

UTS: 1450 MPa

Low tempering temperature ~150 degrees C

35NiCrMo16 (VAR)

4%NiCrMo alloy steel

Shafts and gears

High core strength (1950MPa)

Low tempering temperature ~150 degrees C

S155 (VAR)

40NiSiCrMoV7

Ultra high strength alloy steel

(Si modified 4340)

Cross shaft, driveshafts

High core strength (1930MPa)

Tempering range 250/300 degrees C

Hy-Tuf* (VAR)

25NiSiMnMoCr7

High strength alloy steel

Gears and shafts

Tempering temperature 140/180 degrees C

UTS: 1550MPa

40SiNiCrMoV10

(VIM/VAR)

Ultra high strength alloy steel

Driveshafts,

highly stressed gears

Tempering temperature 300 degrees C

UTS: 2050MPa

*Trade name of Crucible Steel

Essentially all these materials are used in the case hardened condition and cover a wide range of core hardness and strength. Interestingly, most of the materials listed above were developed without motorsport applications in mind!

Consequently, while many alloys were readily and commercially available, there was a need for custom materials designed principally for motorsport applications. In collaboration with Corus Engineering Steels (CES), this led to the development of the new Xtrac materials XM023, XM031 and XM033, as shown in the table below.

Material

Description

Applications

Comments

XM023 (VIM/VAR)

High strength alloy steel

Gearbox internals

Improved bending fatigue and bearing properties. Tempering 200/250 degrees C

XM031 (VIM/VAR)

High molybdenum alloy steel

Gearbox internals

Improved bearing properties

Tempering temperature 350/400 degrees C

XM033 (VIM/VAR)

Ultra high strength alloy steel

Driveshafts,

highly stressed gears

High core strength (2000MPa)

Improved bearing properties

Tempering 300/350 degrees C

The new steel XM023 included nominal alloy additions to provide the required bearing and bend strength properties. By optimising the heat treatment variables, case depth and surface hardness, an approximate 30% increase in bending fatigue life over En36C-VAR was achieved which helped to secure the Formula One drivers' and constructors' championships in 2005 and 2006.

As well as gear ratios, XM023 was also used on the majority of internals in the gearbox including layshaft, mainshaft, dog rings, hubs, selector forks, cross shaft and final drives.

Following the success of XM023, and also because of rule changes where endurance became increasingly more important, a second steel designated XM031 was developed which took advantage of the temper-resistant properties of molybdenum. This enabled the tempering temperature to be raised from ~220 degrees C to 350/400 degrees C while maintaining bearing hardness, thereby opening up greater alternatives with respect to physical vapour deposition coatings (including low friction and solid lubricants).

Click for larger image

In addition, because molybdenum is also a strong carbide-forming element, greater rolling contact fatigue resistance and improved bearing properties can be developed. Bending fatigue resistance is also improved.

The third variant and latest alloy in the material range to be introduced is an ultra high strength (2000MPa) shaft and gear steel, which offers improved bearing properties (to comparable strength steels) due to its higher alloy content.

XM033 offers the advantage of high core strength for shafts, but also improved bearing properties for integrated rolling contact surfaces. Due to the balance of alloying elements, properties of surface hardness (>700Hv), core strength (2000MPa) and elevated tempering temperature (300 degrees C) means the alloy is ideally suited for arduous applications such as cross shafts, integral bearing drive-and clutch-shafts and highly stressed gears.

Properties are generated as a result of a nominal 0.4% core carbon content, an increased silicon level and the addition of vanadium. The result is a readily carburisable material able to simultaneously exhibit bearing properties and high core strength. This material is readily suited to driveshafts with integral bearings, now becoming popular in many motorsport applications.

Conclusion

A family of three new motorsport gear steels has been developed to meet the requirements for increased operating temperature and improved bending and rolling contact fatigue resistance relevant to gear, bearing and shaft component types. Unlike most other steels which have been historically used, these materials were specifically designed to accommodate the requirements encountered in current and foreseeable motorsport applications.

Did you enjoy this article?

Please consider supporting AutoSpeed with a small contribution. More Info...


Share this Article: 

More of our most popular articles.
Evaluating the finished home workshop

DIY Tech Features - 14 October, 2008

Building a Home Workshop, Part 10

Making your own automotive themed clock

DIY Tech Features - 28 October, 2008

DIY Workshop Clock

Important differences to intercooling petrol engine turbos

Technical Features - 10 January, 2008

Diesel Intercooling

Useful parts for nothing

DIY Tech Features - 6 October, 2009

Getting the Good Parts from Scanners!

Laying out a home workshop - and storage options

DIY Tech Features - 30 September, 2008

Building a Home Workshop, Part 8

Country driving skills have almost disappeared - here are some

Special Features - 4 October, 2011

How Not to Die this Week

How they did it

Special Features - 13 October, 2009

Building the Sydney Harbour Bridge

Building a heavy duty mount

DIY Tech Features - 24 July, 2012

Relocating the alternator

What needs to happen to get to the next stage of aerodynamic slipperiness

Technical Features - 29 April, 2008

Analysing Road Car Drag

Using an electronic voltage switch module

DIY Tech Features - 3 February, 2009

How to Electronically Modify Your Car, Part 8

Copyright © 1996-2017 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip