Shopping: Real Estate |  Costumes  |  Guitars
This Issue Archived Articles Blog About Us Contact Us
SEARCH


The Corvette ZR1's LS9 Supercharged Small Block

A monster of an engine

Courtesy of GM

Click on pics to view larger images


It may have only two valves per cylinder and not an overhead cam in sight, but the supercharged 6.2-litre V8 for the 2009 ZR1 Corvette 2009 packs a helluva wallop – no less than 620hp! You won’t find any mention of fuel usage – or much else that reflects wider environmental concerns – but here’s what the insides look like.

Click for larger image

When it arrives next northern summer, the 2009 Chevrolet Corvette ZR1 will be the most powerful and fastest production car ever produced by General Motors, with performance provided by a new, supercharged 6.2L LS9 small-block V-8 engine.

Incorporating the engineering experience already found in the Corvette Z06’s LS7 engine and the new-for-2008 6.2L LS3 of the Corvette, GM Powertrain is targeting 100 horsepower per litre for the LS9, or 620 horsepower (462 kW), and approximately 595 lb.-ft. of torque (807 Nm).

Click for larger image

The enabler of the LS9’s performance is a new, large positive-displacement Roots-type supercharger – with a unique four-lobe design – developed for the engine by Eaton. It is teamed with an integrated charge cooling system that reduces inlet air temperature for maximum performance. The LS9 represents the first of several new, supercharged small-block engines that will be introduced in GM vehicles in the near future, each using superchargers of similar design.

Performance

Click for larger image

More than just its tremendous peak horsepower and torque numbers, the supercharged LS9 makes big power at lower rpm and carries it in a wide arc to 6,600 rpm. GM Powertrain testing shows the engine makes approximately 300 horsepower (224 kW) at 3,000 rpm and nearly 320 lb.-ft. of torque (434 Nm) at only 1,000 rpm. Torque tops 585 lb.-ft. (793 Nm) at about the 4,000-rpm mark, while horsepower peaks at 6,500 rpm.

The engine produces 90 percent of peak torque from 2,600 rpm to 6,000 rpm.

Click for larger image

Heavy-duty and lightweight reciprocating components enable the engine’s confident high-rpm performance, while the large-displacement Eaton supercharger pushes enough air to help the engine maintain power through the upper levels of the rpm band.

The LS9 is assembled by hand at GM’s Performance Build Center, a unique, small-volume engine production facility in Wixom, Mich., that also builds the Corvette Z06’s LS7 engine and other high-performance GM production engines.

Cylinder block and reciprocating parts

Click for larger image

The LS9’s aluminium cylinder block features steel, six-bolt main bearing caps, with enlarged vent windows in the second and third bulkheads for enhanced bay to bay breathing.

Click for larger image

Cast iron cylinder liners – measuring 4.06 inches (103.25 mm) in bore diameter – are inserted in the aluminium block and they are finish-bored and honed with a deck plate installed. The deck plate simulates the pressure and minute dimensional variances applied to the block when the cylinder heads are installed, ensuring a higher degree of accuracy that promotes maximum cylinder head sealing, piston ring fit and overall engine performance.

Click for larger image

Nestled inside the cylinder block is a forged steel crankshaft that delivers the LS9’s 3.62-inch (92 mm) stroke. It features a smaller-diameter ignition-triggering reluctor wheel and a nine-bolt flange – the outer face of the crankshaft on which the flywheel is mounted – that provides more clamping strength. Other non-supercharged 6.2L engines, such as the base Corvette’s LS3, have a six-bolt flange.

Click for larger image

A torsional damper mounted to the front of the crankshaft features a keyway and friction washer, which also is designed to support the engine’s high loads.

Click for larger image

Attached to the crankshaft is a set of titanium connecting rods and forged aluminium pistons, which, when combined with the cylinder heads, delivers a 9.1:1 compression ratio. This combination is extremely durable and lightweight, enabling the LS9’s high-rpm capability.

Cylinder head

Click for larger image

The basic cylinder head design of the LS9 is similar to the L92-type head found on the LS3 V8, but it is cast with a premium A356T6 alloy that is better at handling the heat generated by the supercharged engine – particularly in the bridge area of the cylinder head, between the intake and exhaust valves.

In addition to the special aluminium alloy, each head is created with a rotocast method. Also known as spin casting, the process involves pouring the molten alloy into a rotating mould. This makes for more even distribution of the material and virtually eliminates porosity – air bubbles or pockets trapped in the casting – for a stronger finished product.

Click for larger image

Although the heads are based on the L92 design, they feature swirl-inducing wings that are cast into the intake ports. This improves the mixture motion of the pressurized air/fuel charge. The charge enters the combustion chambers via titanium intake valves that measure 2.16 inches (55 mm) in diameter. Spent gases exit the chambers through 1.59-inch (40.4 mm) hollow stem sodium-filled exhaust valves. The titanium intake and sodium-filled exhaust valves are used for their lightweight and high-rpm capability.

Click for larger image

To ensure sealing of the pressurized engine, unique, four-layer steel head gaskets are used with the LS9’s heads.

Camshaft and valvetrain

Click for larger image

The broad power band enabled by the LS9’s large-displacement supercharger allows it to make strong low-end torque and great high-rpm horsepower, which allowed engineers to specify a camshaft with a relatively low lift of 0.555-inch (14.1 mm) for both the intake and exhaust valves. This low-overlap cam has lower lift and slower valve-closing speeds than the Z06’s 505-horsepower (377 kW) LS7, helping the LS9 – with its approximately 620 horsepower – deliver exemplary idle and low-speed driving qualities.

The camshaft actuates a valvetrain that includes many components, including the lifters, rocker arms and valve springs, of the LS3 engine. However, LS7 retainers are used to support the engine’s high-rpm performance.

Supercharger and charge cooler

Click for larger image

The LS9’s R2300 supercharger is a sixth-generation design from Eaton, with a case that is specific to the Corvette application. The supercharger features a new four-lobe rotor design that promotes quieter and more efficient performance, while its large, 2.3-liter displacement ensures adequate air volume at high rpm to support the engine’s high-horsepower aspiration. Maximum boost pressure is 10.5 psi (0.72 bar).

The supercharger is an engine-driven air pump that contains a pair of long rotors that are twisted somewhat like pretzel sticks. As they spin around each other, incoming air is squeezed between the rotors and pushed under pressure into the engine – forcing more air into the engine than it could draw under “natural” aspiration. The rotors are driven by a pulley and belt that are connected to the engine’s accessory drive system.

Click for larger image

Because the pressurized air is hotter than naturally aspirated air, the LS9 employs a liquid-to-air charge cooling system to reduce inlet air temperature after it exits the supercharger – reducing the inlet air temperature by up to 78 degrees C (140 F). Cooler air is denser and allows the engine to make the most of its high-pressure air charge. The charge cooling system includes a dedicated coolant circuit with a remote-mounted pump and reservoir.

Click for larger image

The design of the supercharger case and its integrated charge cooling system was driven by the space and dimensions afforded under the Corvette’s hood. To that end, the charge cooler was designed as a “dual brick” system, with a pair of low-profile heat exchangers mounted longitudinally on either side of the supercharger. Coupled with the supercharger itself, this integrated design mounts to the engine in place of a conventional intake manifold and is only slightly taller than a non-supercharged 6.2L engine. The air inlet and rotor drive pulley are positioned at the front of the supercharger.

Additional engine details

  • Oiling system

  • Click for larger image

    The LS9 uses a dry-sump oiling system that is similar in design to the LS7’s system, but features a higher-capacity pump to ensure adequate oil pressure at the higher cornering loads the ZR1 is capable of achieving.

    Click for larger image

    An oil-pan mounted oil cooler is integrated, too, along with piston-cooling oil squirters located in the cylinder block. The expanded performance envelope of the Corvette ZR1 required changes to the dry sump system also used in the Z06. System capacity is increased and scavenge performance improved to meet the demands of Chevrolet's highest-performance sportscar.

  • Water pump

  • Click for larger image

    To compensate for the heavier load generated by the supercharger drive system, an LS9-specific water pump with increased bearing capacity is used.

  • Accessory drive system

  • Click for larger image

    To package the accessory drive system in the Corvette’s engine compartment, the supercharger drive was integrated into the main drive system. This required a wider 11-rib accessory drive system to be used with the LS9 in order to support the load delivered by the supercharger.

  • Fuel system

  • Click for larger image

    The LS9 uses high-capacity 48-lb./hr. fuel injectors with centre-feed fuel lines. The centre feed system ensures even fuel flow between the cylinders with less noise. In order to ensure fuel system performance during low speed operation as well as under the extreme performance requirements of wide open throttle (WOT), a dual pressure fuel system was developed. This system operates at 250 kPa at idle and low speed, and ratchets up to 600 kPa at higher-speed and WOT conditions.

  • Throttle body

  • Click for larger image

    An 87-mm, single-bore throttle body is used to draw air into the engine. It is electronically controlled.

  • Rocker covers / ignition coils

  • Click for larger image

    Unique rocker covers with new, direct-mount ignition coils are used. Other Gen IV engines, such as the LS3, feature coil packs mounted to a bracket. The LS9’s direct-mounted coils offer a cleaner appearance and a shorter lead between the coil and spark plug.

    Specifications

    Engine

    6.2L SUPERCHARGED V-8 (LS9)

    Displacement (cu in / cc):

    376 / 6162

    Bore & stroke (in / mm):

    4.06 x 3.62 / 103.25 x 92

    Block material:

    cast aluminium

    Cylinder head material:

    cast aluminium

    Valvetrain:

    overhead valve, 2 valves per cylinder

    Fuel delivery:

    SFI (sequential fuel injection)

    Compression ratio:

    9.1:1

    Horsepower / kW:

    620 / 462 (est.)

    Torque (lb-ft / Nm):

    595 / 823 (est.)

    Recommended fuel:

    premium required

    EPA estimated fuel economy:

    TBD

    Click for larger image

    Did you enjoy this article?

    Please consider supporting AutoSpeed with a small contribution. More Info...


    Share this Article: 

    More of our most popular articles.
    Intercepting analog and digital signals

    DIY Tech Features - 3 March, 2009

    How to Electronically Modify Your Car, Part 12

    Igor Sikorsky's brainchild

    Technical Features - 18 May, 2010

    The First Helicopter

    Making your own automotive themed clock

    DIY Tech Features - 28 October, 2008

    DIY Workshop Clock

    Evaluating the finished home workshop

    DIY Tech Features - 14 October, 2008

    Building a Home Workshop, Part 10

    Making it easier to work on your car

    DIY Tech Features - 12 June, 2012

    The Spit

    DIY testing of your engine's water pump

    Technical Features - 11 June, 2008

    Water Pump Testing

    Then the world's most powerful six cylinder passenger car diesel

    Technical Features - 6 June, 2005

    BMW's Twin Turbo Diesel

    The rear suspension

    DIY Tech Features - 9 June, 2009

    Chalky, Part 5

    A bloody nightmare...

    DIY Tech Features - 6 March, 2012

    A New Home Workshop, Part 5

    Reducing fuel use through electronic tweaks

    DIY Tech Features - 27 September, 2006

    Electronic Ways to Improve Your Fuel Economy

    Copyright © 1996-2020 Web Publications Pty Limited. All Rights ReservedRSS|Privacy policy|Advertise
    Consulting Services: Magento Experts|Technologies : Magento Extensions|ReadytoShip